96-120 WATT ITE POWER SUPPLIES
DESCRIPTION
PUP96N3/PUP120N3 SERIES
The PUP96N3/PUP120N3 series of AC/DC switching power
RoHS
supplies are for 96-120 watts of continuous output power.
They are enclosed in a 94V-0 rated plastic case with an
inlet of the IEC320/C14 or IEC320/C6 to mate with
interchangeable cord for world-wide use. All models meet
EN55032 and FCC class B emission limits, and comply
with UL, CSA, IEC and CE requirements.
FEATURES
l No load power consumption less than 0.15 W
l Compliant with DoE level VI requirements
l Meet Energy Star EPS2.0 /ErP EC No 278/2009 (Lot 7)
SAFETY STANDARD APPROVALS
l Meet EU CoC EPS V5 Tier 2
l Operating altitude up to 5000 meters
UL 62368-1, CSA C22.2 No. 62368-1
l Overvoltage protection (latch)
File No. E190414
l Short-circuit protection (auto-recovery)
l Overpower protection (auto-recovery)
l Over temperature protection (latch)
l High Efficiency 89% TUV EN 62368-1
l With PFC circuit
l 100% burn-in at full rated load
l Compliant with RoHS requirements
GENERAL SPECIFICATIONS
Hold-up time: 10 ms minimum at 100 VAC
Turn on delay time: 3 s maximum at 100 VAC
INPUT SPECIFICATIONS Power factor: 0.95 typical
Input voltage:
90-264 VAC
Efficiency: 89% minimum at 110 VAC or 240 VAC.
Input frequency: 47-63 Hz
Line regulation: 0.5% maximum at full load
Input current: 1.3 A (rms) for 115 VAC
Inrush current: 100 A @ 115 Vac or 200 A @ 230 Vac at 25
0.7 A (rms) for 230 VAC
cold start
Earth Leakage current: 250 A max. @ 264 VAC, 60 Hz
Withstand voltage: 4242 VDC from input to output
2500 VDC from input to ground
MTBF: 200,000 hours at full load at 25 ambient,
OUTPUT SPECIFICATIONS
calculated per SR332
Output voltage /current: See rating chart.
Maximum output power: See rating chart.
Ripple and noise: 350 mV peak to peak maximum
EMC Performance
Overvoltage protection: Set at 125-155% of its nominal
EN55032: Class B conducted, Class B radiated
output voltage
Overcurrent protection: All models protected to short
FCC: Class B conducted, Class B radiated
circuit conditions (auto-recovery)
VCCI: Class B conducted, Class B radiated
All outputs 0.04% / maximum
Temperature coefficient:
EN61000-3-2: Harmonic distortion, Class D
Transient response: Maximum excursion of 4% or better on
EN61000-3-3: Line flicker
all models, recovering to 1% of final
EN55024
value within 500 us after a 25% step
load change
EN61000-4-2: ESD,8 KV air and 4 KV contact
EN61000-4-3: Radiated immunity, 3 V/m
EN61000-4-4: Fast transient/burst, 1 KV
EN61000-4-5: Surge, 1 KV diff., 2 KV com.
EN61000-4-6: Conducted immunity, 3 Vrms
ENVIRONMENTAL SPECIFICATIONS
EN61000-4-8: Magnetic field immunity, 1 A/m
Operating temperature: 0 to +40
EN61000-4-11: Voltage dip immunity, 30% reduction for 500
Storage temperature: -20 to +80
ms, and >95% reduction for 10 ms
Operating humidity: 20% to 80% non-condensing
Storage humidity: 10% to 90% non-condensing
45UNIVERSAL INPUT PUP96N3/PUP120N3 ITE SERIES
OUTPUT VOLTAGE/CURRENT RATING CHART
Output Average Active
efficiency (typical)
Min. Max. Ripple & Max.
(1) (2)
@ 115 / 230 Vac
Model V1 Current Current Tol. Noise Power
PUP96N3-12
12 V 0 A 8.00 A 5% 350 mV 96 W 89 /90%
PUP96N3S-12
12 V 0 A 8.00 A 5% 350 mV 96 W 89 /90%
PUP120N3-12
12 V 0 A 10.00 A 5% 350 mV 120 W 89 /90%
PUP120N3S-12
12 V 0 A 10.00 A 5% 350 mV 120 W 89 /90%
PUP120N3-14
24 V 0 A 5.00 A 5% 350 mV 120 W 89 /91%
PUP120N3S-14
24 V 0 A 5.00 A 5% 350 mV 120 W 89 /91%
PUP120N3-18 48 V 0 A 2.50 A 5% 350 mV 120 W 89 /91%
PUP120N3S-18 48 V 0 A 2.50 A 5% 350 mV 120 W 89 /91%
PUP120N3-19
54 V 0 A 2.22 A 5% 350 mV 120 W 89 /91%
PUP120N3S-19
54 V 0 A 2.22 A 5% 350 mV 120 W 89 /91%
NOTES:
1. PUP120N3 models are equipped with IEC320/C14 inlet, and PUP120N3S models are equipped with IEC320/C6 inlet.
2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load
ranges, and with a 47 F tantalum capacitor in parallel with a 0.1 F ceramic capacitor across the output.
MECHANICAL SPECIFICATIONS
NOTES:
1. Dimensions shown in inches [mm]
2. Tolerance 0.02 [0.5] maximum
3. Weight: 417 grams (0.92 lbs.) approx.
4. V1 return (-) is electrically connected to incoming Earth Ground through a 1M ohm resistor as standard.
PIN CHART
SHELL OF
PIN NO. 1 2 3 4
CONNECTOR
Polarity +V1 +V1 V1 Return V1 Return V1 Return
46