150 WATT ITE POWER SUPPLIES
DESCRIPTION
PUP150N3 SERIES
The PUP150N3 series of AC/DC switching power supplies are
for 150 watts of continuous output power. They are
RoHS
enclosed in a 94V-0 rated plastic case with an inlet of the
IEC320/C14 or IEC320/C6 to mate with interchangeable
cord for world-wide use. All models meet EN55032 and
FCC class B emission limits, and comply with UL, CSA,
IEC and CE requirements.
FEATURES
l No load power consumption less than 0.15 W
l Compliant with DoE level VI requirements
l Meet Energy Star EPS2.0 /ErP EC No 278/2009 (Lot 7)
l Meet EU CoC EPS V5 Tier 2
SAFETY STANDARD APPROVALS
l Operating altitude up to 5000 meters
l Overvoltage protection (latch)
UL 62368-1, CSA C22.2 No. 62368-1
l Short-circuit protection (auto-recovery)
File No. E190414
l Overpower protection (auto-recovery)
l Over temperature protection (latch)
l High Efficiency 89%
l With PFC circuit
TUV EN 62368-1
l 100% burn-in at full rated load
l Compliant with RoHS requirements
GENERAL SPECIFICATIONS
INPUT SPECIFICATIONS Hold-up time: 10 ms minimum at 100 VAC
Input voltage:
90-264 VAC Turn on delay time: 3 s maximum at 100 VAC
Input frequency:
47-63 Hz
Power factor: 0.95 typical
Input current: 1.6 A (rms) for 115 VAC
Efficiency: 89% minimum at 110 VAC or 240 VAC.
0.8 A (rms) for 230 VAC
Line regulation: 0.5% maximum at full load
Earth Leakage current: 250 A max. @ 264 VAC, 60 Hz
Inrush current: 100 A @ 115 Vac or 200 A @ 230 Vac at 25
cold start
Withstand voltage: 4242 VDC from input to output
2500 VDC from input to ground
OUTPUT SPECIFICATIONS
MTBF: 200,000 hours at full load at 25 ambient,
Output voltage /current: See rating chart.
calculated per SR332
Maximum output power: See rating chart.
Ripple and noise: 350 mV peak to peak maximum
Overvoltage protection: Set at 125-155% of its nominal
output voltage
EMC Performance
Overcurrent protection: All models protected to short
circuit conditions (auto-recovery) EN55032: Class B conducted, Class B radiated
All outputs 0.04% / maximum
Temperature coefficient:
FCC: Class B conducted, Class B radiated
Transient response: Maximum excursion of 4% or better on
VCCI: Class B conducted, Class B radiated
all models, recovering to 1% of final
EN61000-3-2: Harmonic distortion, Class D
value within 500 us after a 25% step
EN61000-3-3: Line flicker
load change
EN55024
EN61000-4-2: ESD,8 KV air and 4 KV contact
EN61000-4-3: Radiated immunity, 3 V/m
ENVIRONMENTAL SPECIFICATIONS
EN61000-4-4: Fast transient/burst, 1 KV
Operating temperature: 0 to +40 EN61000-4-5: Surge, 1 KV diff., 2 KV com.
Storage temperature: -20 to +80
EN61000-4-6: Conducted immunity, 3 Vrms
Operating humidity: 20% to 80% non-condensing
EN61000-4-8: Magnetic field immunity, 1 A/m
Storage humidity: 10% to 90% non-condensing
EN61000-4-11: Voltage dip immunity, 30% reduction for 500
ms, and >95% reduction for 10 ms
47UNIVERSAL INPUT PUP150N3 ITE SERIES
OUTPUT VOLTAGE/CURRENT RATING CHART
Output Average Active
efficiency (typical)
Ripple &
(1) (2)
Model V1 Min. Current Max. Current Tol. Noise Max. Power @ 115 / 230 Vac
PUP150N3-12 12 V 0 A 12.5 A 5% 350 mV 150 W 90.4 /90.9%
PUP150N3S-12 12 V 0 A 12.5 A 5% 350 mV 150 W 90.4 /90.9%
PUP150N3-13-2 19 V 0 A 7.89 A 5% 90.5 /91.4%
350 mV 150 W
PUP150N3S-13-2 19 V 7.89 A 5% 90.5 /91.4%
0 A 350 mV 150 W
PUP150N3-14 24 V 0 A 6.25 A 5% 350 mV 150 W 91.4 /92.4%
PUP150N3S-14 24 V 0 A 6.25 A 5% 350 mV 150 W 91.4 /92.4%
PUP150N3-19 54 V 2.77 A 5% 91.5 /92.4%
0 A 350 mV 150 W
PUP150N3S-19 54 V 2.77 A 5% 91.5 /92.4%
0 A 350 mV 150 W
NOTES:
1. PUP150N3 models are equipped with IEC320/C14 inlet, and PUP150N3S models are equipped with IEC320/C6 inlet.
2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load
ranges, and with a 47 F tantalum capacitor in parallel with a 0.1 F ceramic capacitor across the output.
MECHANICAL SPECIFICATIONS
NOTES:
1. Dimensions shown in inches [mm]
2. Tolerance 0.02 [0.5] maximum
3. Weight: 400 grams (0.88 lbs.) approx.
4. Refer to Section titled OPTIONAL OUTPUT CONNECTORS. Change suffix assigned for a selected connector to a wanted model
number, e.g. PUP150N3-14-B1, for ordering.
5. The length of output cable for output voltage 12V is 59.06 [1500.0].
6. V1 return (-) is electrically connected to incoming Earth Ground through a 1K ohm resistor as standard.
PIN CHART
SHELL OF
PIN NO.
1 2 3 4
CONNECTOR
Polarity +V1 +V1 V1 Return V1 Return V1 Return
48