230 WATT ITE POWER SUPPLIES
DESCRIPTION
PUP230N3 SERIES
The PUP230N3 series of AC/DC switching power supplies are
for 230 watts of continuous output power. They are
RoHS
enclosed in a 94V-0 rated plastic case with an IEC320/C14
inlet to mate with interchangeable cord for world-wide use.
All models meet EN55032 and FCC class B emission
limits, and comply with UL, CSA, IEC and CE
requirements.
FEATURES
l No load power consumption less than 0.15 W
l Compliant with DoE level VI requirements
l Meet Energy Star EPS2.0 /ErP EC No 278/2009 (Lot 7)
l Meet EU CoC EPS V5 Tier 2
SAFETY STANDARD APPROVALS
l Operating altitude up to 5000 meters
l Overvoltage protection (latch)
UL 62368-1, CSA C22.2 No. 62368-1
l Short-circuit protection (auto-recovery)
File No. E190414
l Overpower protection (auto-recovery)
l Over temperature protection (latch)
l High Efficiency 89%
l With PFC circuit
TV EN 62368-1
l 100% burn-in at full rated load
l Compliant with RoHS requirements
GENERAL SPECIFICATIONS
INPUT SPECIFICATIONS Hold-up time: 10 ms minimum at 100 VAC
Input voltage:
90-264 VAC Turn on delay time: 3 s maximum at 100 VAC
Input frequency:
47-63 Hz
Power factor: 0.95 typical
Input current: 2.3 A (rms) for 115 VAC
Efficiency: 89% minimum at 110 VAC or 240 VAC.
1.2 A (rms) for 230 VAC
Line regulation: 0.5% maximum at full load
Earth Leakage current:: 250 A max. @ 264 VAC, 60 Hz
Inrush current: 100 A @ 115 Vac or 200 A @ 230 Vac at 25
cold start
Withstand voltage: 4242 VDC from input to output
OUTPUT SPECIFICATIONS
2500 VDC from input to ground
Output voltage /current: See rating chart.
MTBF: 200,000 hours at full load at 25 ambient,
Maximum output power: See rating chart.
calculated per SR332
Ripple and noise: 350 mV peak to peak maximum
Overvoltage protection: Set at 125-155% of its nominal
output voltage
Overcurrent protection: All models protected to short
circuit conditions (auto-recovery) EMC Performance
All outputs 0.04% / maximum
Temperature coefficient:
EN55032: Class B conducted, Class B radiated
Transient response: Maximum excursion of 4% or better on
FCC: Class B conducted, Class B radiated
all models, recovering to 1% of final
VCCI: Class B conducted, Class B radiated
value within 500 us after a 25% step
EN61000-3-2: Harmonic distortion, Class D
load change
EN61000-3-3: Line flicker
EN55024
EN61000-4-2: ESD,8 KV air and 4 KV contact
ENVIRONMENTAL SPECIFICATIONS
EN61000-4-3: Radiated immunity, 3 V/m
Operating temperature: 0 to +40
EN61000-4-4: Fast transient/burst, 1 KV
Storage temperature: -20 to +80
EN61000-4-5: Surge, 1 KV diff., 2 KV com.
Operating humidity: 20% to 80% non-condensing
EN61000-4-6: Conducted immunity, 3 Vrms
Storage humidity: 10% to 90% non-condensing
EN61000-4-8: Magnetic field immunity, 1 A/m
EN61000-4-11: Voltage dip immunity, 30% reduction for 500
ms, and >95% reduction for 10 ms
51UNIVERSAL INPUT PUP230N3 ITE SERIES
OUTPUT VOLTAGE/CURRENT RATING CHART
Output Average Active
efficiency (typical)
Ripple &
(1) (2)
Model V1 Min. Current Max. Current Tol. Noise Max. Power @ 115 / 230 Vac
230 W
PUP230N3-13-2-1 19.5 V 0 A 11.79 A 5% 350 mV 89 /91%
PUP230N3-14 24 V 0 A 9.58 A 5% 350 mV 230 W 91 /93%
NOTES:
1. PUP230N3 models are equipped with IEC320/C14 inlet.
2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load
ranges, and with a 47 F tantalum capacitor in parallel with a 0.1 F ceramic capacitor across the output.
MECHANICAL SPECIFICATIONS
NOTES:
1. Dimensions shown in inches [mm]
2. Tolerance 0.02 [0.5] maximum
3. Weight: 600 grams (1.33 lbs.) approx.
4. V1 return (-) is electrically connected to incoming Earth Ground through a 1K ohm resistor as standard.
PIN CHART
PIN NO. 1 2 3 4 5 6
Polarity V1 Return V1 Return V1 Return +V1 +V1 +V1
52