330 WATT ITE POWER SUPPLIES
DESCRIPTION
PUP330N3 SERIES
The PUP330N3 series of AC/DC switching power supplies are
for 330 watts of continuous output power. They are
RoHS
enclosed in a 94V-0 rated plastic case with an inlet of the
IEC320/C14 to mate with interchangeable cord for
world-wide use. All models meet EN55032 and FCC class
B emission limits, and comply with UL, CSA, IEC and CE
requirements.
FEATURES
l Compliant with DoE level VI requirements
l Meet Energy Star EPS2.0 /ErP EC No 278/2009 (Lot 7)
l Meet EU CoC EPS V5 Tier 2
l High Efficiency 89%
SAFETY STANDARD APPROVALS
l No load power consumption less than 0.5 W
l With PFC circuit
UL 62368-1, CSA C22.2 No. 62368-1
l Operating altitude up to 5000 meters
File No. E190414
l Overvoltage protection (latch)
l Short-circuit protection (auto-recovery)
l Overpower protection (auto-recovery)
TUV EN 62368-1
l Over temperature protection (latch)
l Compliant with RoHS requirements
GENERAL SPECIFICATIONS
INPUT SPECIFICATIONS
Hold-up time: 10 ms minimum at 100 VAC
Input voltage:
90-264 VAC
Turn on delay time: 3 s maximum at 100 VAC
Input frequency: 47-63 Hz
Power factor: 0.95 typical
Input current: 3.4 A (rms) for 115 VAC
Efficiency: 89% minimum at 110 VAC or 240 VAC.
1.7 A (rms) for 230 VAC
Earth leakage current: 250 A max. @ 264 VAC, 60 Hz Line regulation: 0.5% maximum at full load
Inrush current: 100 A @ 115 Vac or 200 A @ 230 Vac at 25
cold start
Withstand voltage: 4242 VDC from input to output
2500 VDC from input to ground
OUTPUT SPECIFICATIONS MTBF: 200,000 hours at full load at 25 ambient,
calculated per SR332
Output voltage /current: See rating chart.
Maximum output power: See rating chart.
Ripple and noise: 350 mV peak to peak maximum
Overvoltage protection: Set at 125-155% of its nominal
EMC Performance
output voltage
EN55032: Class B conducted, Class B radiated
Overcurrent protection: All models protected to short
circuit conditions (auto-recovery) FCC: Class B conducted, Class B radiated
All outputs 0.04% / maximum
Temperature coefficient:
VCCI: Class B conducted, Class B radiated
Transient response: Maximum excursion of 4% or better on
EN61000-3-2: Harmonic distortion, Class D
all models, recovering to 1% of final
EN61000-3-3: Line flicker
value within 500 us after a 25% step
EN55024
load change
EN61000-4-2: ESD,8 KV air and 4 KV contact
EN61000-4-3: Radiated immunity, 3 V/m
EN61000-4-4: Fast transient/burst, 1 KV
ENVIRONMENTAL SPECIFICATIONS
EN61000-4-5: Surge, 1 KV diff., 2 KV com.
Operating temperature: 0 to +40
EN61000-4-6: Conducted immunity, 3 Vrms
Storage temperature: -20 to +80
EN61000-4-8: Magnetic field immunity, 1 A/m
Operating humidity: 20% to 80% non-condensing
EN61000-4-11: Voltage dip immunity, 30% reduction for 500
Storage humidity: 10% to 90% non-condensing ms, and >95% reduction for 10 ms
55UNIVERSAL INPUT PUP330N3 ITE SERIES
OUTPUT VOLTAGE/CURRENT RATING CHART
Output Average Active
efficiency (typical)
Ripple &
(1) (2)
Model V1 Min. Current Max. Current Tol. Noise Max. Power @ 115 / 230 Vac
330 W
PUP330N3-13-2-1 19.5 V 0 A 16.90 A 5% 350 mV 89 /91%
PUP330N3-14 24 V 0 A 13.75 A 5% 350 mV 330 W 91 /93%
NOTES:
1. PUP330N3 models are equipped with IEC320/C14 inlet.
2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load
ranges, and with a 47 F tantalum capacitor in parallel with a 0.1 F ceramic capacitor across the output.
MECHANICAL SPECIFICATIONS
NOTES:
1. Dimensions shown in inches [mm]
2. Tolerance 0.02 [0.5] maximum
3. Weight: 750 grams (1.51 lbs.) approx.
4. V1 return (-) is electrically connected to incoming Earth Ground through a 1K ohm resistor as standard.
PIN CHART
PIN NO. 1 2 3 4
Polarity +V1 +V1 V1 Return V1 Return
56