90 WATT ITE POWER SUPPLIES
DESCRIPTION
PUP90N3 SERIES
The PUP90N3 series of AC/DC switching power supplies are for
RoHS
90 watts of continuous output power. They are enclosed in a 94V-0
rated plastic case with IEC320/C14 or IEC320/C6 inlet to mate
with interchangeable cord for world-wide use. All models meet
EN55032, EN55024 and FCC class B emission limits, and
comply with UL, CSA, IEC and CE requirements.
FEATURES
l No load power consumption less than 0.15W
l Compliant with DoE level VI requirements
l Meet energy star EPS2.0 /ErP EC No 278/2009 (lot 7)
l Meet EU CoC EPS V5 Tier2
SAFETY STANDARD APPROVALS
l Operating altitude up to 5000 meters
UL 62368-1, CSA C22.2 No. 62368-1
l Overvoltage protection (latch)
File No. E190414
l Short circuit protection (auto-recovery)
l Overcurrent protection (auto-recovery)
l Over temperature protection (latch)
TV EN 62368-1
l High efficiency, 89%
l With PFC circuit
l 100% burn-in at full rated load
l Compliant with RoHS requirements
GENERAL SPECIFICATIONS
Power factor: 0.90 Typical at 115 VAC
INPUT SPECIFICATIONS
Efficiency: 89% minimum at full load
Input voltage: 90-264 VAC
Hold-up time: 10 ms minimum at 100 VAC
Input frequency: 47-63 Hz
Line regulation: 0.5% maximum at full load
Input current: 1.0 A (rms) for 115 VAC
Inrush current: 60 A @ 115 VAC or 120 A @ 230 VAC, at 25
0.5 A (rms) for 230 VAC
cold start
Earth Leakage current: 250 A max. @ 264 VAC, 60 Hz
Withstand voltage: 4242 VDC from input to output
2500 VDC from input to ground
MTBF: 200,000 hours at full load at 25 ambient,
calculated per SR332
OUTPUT SPECIFICATIONS
Output voltage /current: See rating chart.
Maximum output power: See rating chart.
EMC Performance
Ripple and noise: See rating chart.
EN55032: Class B conducted, class B radiated
Overvoltage protection: Provided and set at 110-155% of its
FCC: Class B conducted, class B radiated
nominal output voltage
Overcurrent protection: Protected to short circuit conditions VCCI: Class B conducted, class B radiated
EN61000-3-2: Harmonic distortion, class D
Temperature coefficient: 0.04% / maximum
EN61000-3-3: Line flicker
Transient response: Maximum excursion of 4% or better on
all models, recovering to 1% of final EN55024
value within 500 us after a 25% step
EN61000-4-2: ESD, 8 KV air and 4 KV contact
load change
EN61000-4-3: Radiated immunity, 3 V/m
EN61000-4-4: Fast transient/burst, 1 KV
EN61000-4-5: Surge, 1 KV diff., 2 KV com.
EN61000-4-6: Conducted immunity, 3 Vrms
ENVIRONMENTAL SPECIFICATIONS
EN61000-4-8: Magnetic field immunity, 1 A/m
Operating temperature: 0 to +40
EN61000-4-11: Voltage dip immunity, 30% reduction for 500
Storage temperature: -20 to +80
ms and >95% reduction for 10 ms
Operating humidity: 20% to 80% non-condensing
Storage humidity: 10% to 90% non-condensing
43UNIVERSAL INPUT PUP90N3 ITE SERIES
OUTPUT VOLTAGE/CURRENT RATING CHART
Output Average Active
Efficiency (typical)
Ripple &
(1) (2)
Model V1 Min. Current Max. Current Tol. Noise Max. Power @ 115 / 230 Vac
19 V 0 A 4.74 A 5% 350 mV 90 W 89 /89%
PUP90N3-13-2
PUP90N3S-13-2 19 V 0 A 4.74 A 5% 350 mV 90 W 89 /89%
PUP90N3-14 24 V 0 A 3.75 A 5% 350 mV 90 W 90 /90%
PUP90N3S-14 24 V 0 A 3.75 A 5% 350 mV 90 W 90 /90%
48 V 0 A 1.88 A 5% 350 mV 90 W 91 /91%
PUP90N3-18
48 V 0 A 1.88 A 5% 350 mV 90 W 91 /91%
PUP90N3S-18
PUP90N3-19 54 V 0 A 1.67 A 5% 350 mV 90 W 90 /90%
PUP90N3S-19 54 V 0 A 1.67 A 5% 350 mV 90 W 90 /90%
NOTES:
1. PUP90N3 models are equipped with IEC320/C14 inlet, and PUP90N3S models with IEC320/C6 inlet.
2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load
ranges, and with a 47 F electrolytic capacitor in parallel with a 0.1 F ceramic capacitor across the output.
MECHANICAL SPECIFICATIONS
NOTES:
1. Dimensions shown in inches [mm]
2. Tolerance 0.02 [0.5] maximum
3. Weight: 360 grams (0.79 lbs.) approx.
4. Output return (-) is electrically connected to incoming Earth Ground through a 1M ohm resistor as standard.
PIN CHART
PIN NO. CONNECTION
Polarity
44