t OM| ` K = = OULQLMP = = NMWNV= ~ = = m~= N
Resistors
Vitreous Enamelled
Make Possible
Welwyn Components
Wirewound Resistors
Vitreous Enamelled
Wirewound Resistors
W20 Series
W20 Series
CECC approved
Suitable for harsh environments
CECC approved
Impervious lead free vitreous enamel coating
Suitable for harsh environments
Overload characteristics ideal
Imper vious lead free vitreous enamel coating
for protection circuits
Overload characteristics ide al for protection circuits
HighHigh s tstabilityability and and reliability reliability
High p ower dissipation for size
High power dissipation for size
All Pb-free parts comply with EU Directive 2011/65/EU (RoHS2)
Electrical Data
Commercial W21 W215 W22 W23 W24
Power rating at 25C watts 3.0 5.0 7.0 10.5 14.0
Resistance range at 1% tolerance ohms 1R to 10K 1R to 15K 1R to 22K 1R to 60K 1R to 100K
2% tolerance ohms 0R5 to 10K 0R5 to 15K 0R5 to 22K 1R to 60K 1R to 100K
5% tolerance ohms 0R1 to 10K 0R1 to 15K 0R1 to 22K 0R15 to 60K 0R2 to 100K
TCR (-55 to 200C) ppm/C Typically: <+-75 Maximum: +-200
BS CECC 40-201-002 Requirements Style JB HB KB LB MB
Power rating at 25C watts 2.9 5.0 7.0 10.5 14.0
Power rating at 70C watts 2.5 4.3 6.0 9.0 12.0
Resistance range at 1% tolerance ohms 1R to 10K 1R to 15K 1R to 20K 1R to 56K 1R to 100K
2% tolerance ohms 0R5 to 10K 0R5 to 15K 0R5 to 20K 1R to 56K 1R to 100K
5% tolerance ohms 0R1 to 10K 0R1 to 15K 0R1 to 20K 0R15 to 56K 0R2 to 100K
TCR (-55 to 200C) ppm/C 5 ohms < 10 ohms: 400 10 ohms: 200
This table indicates the CECC specification requirements, and these are met or exceeded by the corresponding W20 series products
Applicable to commercial and approved ranges
Limiting element voltage volts 100 160 200 500 750
Standard values E24 preferred. Other values to special order
Thermal impedance C/watt 88 58 44 29 22
Ambient temperature range C -55 to 200
Physical Data
Dimensions (mm) and Weight (g)
Type L max D max f min d nom Wt.nom
W21 12.7 5.6 22.75 0.8 1
W215 22.0 7.0 23.1 0.8 2
d
W22 22.0 8.0 23.1 0.8 2
D
L
f
W23 38.0 8.0 - 0.8 3.5
W24 53.5 8.0 - 0.8 5
400
Construction
W215
W21 W23 W24
A high purity ceramic substrate is assembled with interference fit end caps to which are
W22
welded the termination wires. The resistive element is wound on the substrate and welded to
300
the caps; the vitreous enamel protective coating is then applied.
Terminations
200
Material Copper clad steel wire, nickel plated and solder-coated.
Strength The terminations meet the requirements of IEC 68.2.21.
100 Solderability The terminations meet the requirements of IEC 115-1, Clause 4.17.3.2.
Length W23s and W24s are not supplied on tape. Minimum lead length is 30 mm.
Marking
0
0 5 10 15 20
The resistors are legend marked with type reference, resistance value and tolerance. Values are
marked in accordance with IEC 62.
Dissipation Watts
General Note
General Note
Welwyn Components reserves the right to make changes in product specification without notice or liability.
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to Welwyns own data and is considered accurate at time of going to print. A subsidiary of
All information is subject to TT Electronics own data and is considered accurate at time of going to print.
TT electronics plc
www.ttelectronicsresistors.com
Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK
TT Electronics plcTelephone: +44 (0) 1670 822181 Facsimile: +44 (0) 1670 829465 Email: info@welwyn-tt.com Website: www.welwyn-tt.com
11.14
Temperature Rise Ct OM| ` K = = OULQLMP = = NMWNV= ~ = = m~= O
Vitreous Enamelled
Wirewound Resistors Make Possible
Vitreous Enamelled
W20 Series
Wirewound Resistors
Welwyn Components
W20 Series
Solvent Resistance
The body protection and marking are resistant to all normal industrial cleaning solvents suitable for printed circuits
Flammability
Solvent Resistance
Flammability All materials used in the construction of W series resistors
The body protection and marking are resistant to all normal
are inorganic and inherently non burning.
industrial cleaning solvents suitable for printed circuits.
All materials used in the construction of W20 series resistors are inorganic and inherently non-burning.
Performance Data
CECC 40201-002 Actual Performance
Requirements Maximum Typical
Load at commercial rating: 1000 hrs at 25C R% 5 3.5
Load at CECC rating: 1000 hours at 25C R% 5 5 3.5
Dry heat: 1000 hours at 200C R% 52 1
Shelf life: 12 months at room temperature R% not specified 0.03 0.02
Derating see derating curve
Short term overload R% 1 1.0 0.2
Climatic R% 5 0.5 0.2
Climatic category R% 55/200/56
Long term damp heat R% 5 0.05 0.02
Temperature rapid change R% 1 0.5 0.2
Resistance to solder heat R% 1 0.25 0.03
Vibration and bump R% 1 0.25 0.05
Noise (in decade of frequency) v/v not specified zero zero
Robustness R% 1 0.4 0.05
Insulation resistance ohms not specified > 1G ohm > 1G ohm
Voltage Proof volts not specified 500 min 500 min
Pulse handling data available by request
Application Notes
Packaging
The termination should not be bent closer than 1.6mm from For W21 and W215 the standard method of packaging is
the body, and the recommended minimum bend radius is taped in Ammo Packs. For W22 the standard method of
1.2mm. The terminations are solderable to within 4mm from packaging is taped and reeled. W23s and W24s are
available only as loose packed in boxes.
the body. When cold, vitreous enamel has excellent insulation
resistance. In common with all insulants the specific resistance
of the enamel decreases with increase in temperature.
Therefore, resistors operated at near maximum temperature
cannot be classed as insulated and should not be used in
contact with any conducting material. Care must be taken
10
when determining clearance distance between the resistor
body and the printed circuit board or other components to
ensure these are not over heated. Resistance is measured
6mm from body. f f
1 2
6 b 6
f f 1.4 mm
1 2
116 Derating Curve
100
54
Type b
W21 632
0 W215 732
25 70 200 315
W22 732
Ambient temperature C
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics own data and is considered accurate at time of going to print.
www.ttelectronicsresistors.com
TT Electronics plc
11.14
Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 Facsimile: +44 (0) 1670 829465 Email: info@welwyn-tt.com Website: www.welwyn-tt.com
% of Rated Power