T60404-N4646-X410 Vacuumschmelze

Item no.: T60404-N4646-X410 SPECIFICATION VACUUM SCHM ELZE K-No.: 24616 Date: 28.01.2008 50 A Current Sensor For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit (electronic circuit) Customers Part no.: Page 1 of 2 Customer: Standard type Description Characteristics Applications Mainly used for stationary operation in industrial Closed loop (compensation) Excellent accuracy applications: Current Sensor with magnetic Very low offset current field probe AC variable speed drives and servo motor Very low temperature dependency and offset drives Printed circuit board mounting current drift Static converters for DC motor drives Casing and materials UL-listed Very low hysteresis of offset current Battery supplied applications Low response time Switched Mode Power Supplies (SMPS) Wide frequency bandwidth Power Supplies for welding applications Compact design Uninterruptable Power Supplies (UPS) Reduced offset ripple 1) Electrical data Ratings I Primary nominal r.m.s. current 50 A PN R Measuring resistance V = 12V 10 ... 200 M C V = 15V 22 400 C I Secondary nominal r.m.s. current 50 mA SN KN Turns ratio 13 : 1000 1) Accuracy Dynamic performance data min. typ. max. Unit I Max. measuring range P,max V = 12V, R = 10 (t = 10sec) 112 A C M max V = 15V, R = 22 (t = 10sec) 128 A C M max X Accuracy I , T = 25C 0.1 0.5 % PN A Linearity 0.1 % L I Offset current I =0, T = 25C 0.02 0.1 mA 0 P A tr Response time 500 ns t (I ) Delay time at di/dt = 100 A/s 200 ns P,max f Frequency bandwidth DC...200 kHz 1) General data min. typ. max. Unit T Ambient operating temperature -40 +85 C A T Ambient storage temperature -40 +90 C S m Mass 13.5 g V Supply voltage 11.4 12 or 15 15.75 V C I Current consumption 18,5 mA C Constructed and manufactored and tested in accordance with EN 61800-5-1 (Pin 1 - 6 to Pin 7 9) Reinforced insulation, Insulation material group 1, Pollution degree 2 S clearance (component without solder pad) 10.2 mm clear S creepage (component without solder pad) 10.2 mm creep V System voltage overvoltage category 3 RMS 600 V sys V Working voltage (table 7 acc. to EN61800-5-1) RMS 1020 V work U Rated discharge voltage peak value 1400 V PD Date Name Isuue Amendment 28.01.08 Le 81 Date changed. Insignificant freig.: Heu. Hrsg.: KB-E Bearb: KB-E: Le KB-PM: KRe. SA released editor designer check check Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages. Item no.: T60404-N4646-X410 SPECIFICATION VACUUM SCHM ELZE K-No.: 24616 Date: 28.01.2008 50 A Current Sensor For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit (electronic circuit) Customers Part no.: Page 2 of 2 Customer: Standard type Mechanical outline (mm): General tolerances DIN ISO 2768-c Connections: Toleranz der Stiftabstnde 33,25 0,2mm 1...6: 1,5 mm 7...9: 0,6x0,7 mm 1,905 Z Einzelheit 79 46 Z 1,74 0,6 11,43 0,7 Marking: 1,29 1 3 (2,64) 2x2,54 12,7 7,75 14,45 F DC 4646X410 F DC 7,6 21 3,50.5 0,65 3x 0,7x0,6 6x 1,5 DC = Date Code F= Factory Schematic diagram Ip 8 + V C + 1...3 7 I + S + C A R M - 4...6 9 - V C M Possibilities of wiring for V = 15V ( T = 85C, R = 22 ) C A M primary primary current output current turns ratio primary wiring windings RMS maximal RMS resistance N I A A I (I ) mA K R mW P P P,max S P N P 3 1 > 1 50 128 50 1:1000 0,12 . > 4 6 1 3 > 2 20 64 40 2:1000 0,54 > 6 4 1 . 3 . > 3 15 43 45 3:1000 1,1 . > 6 4 Temperature of the primary conductor should not exceed 100C. Additional information is obtainable on request. This specification is no declaration of warranty acc. BGB 443 dar. freig.: Heu. Hrsg.: KB-E Bearb: KB-E: Le KB-PM: KRe. SA released editor designer check check Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages.