Products General Purpose Prototyping Boards VECTORBORD Vectorbord Prototyping Boards with punched holes are convenient, economical tools for assembling circuit components-and cost efficient alternatives to custom designs. Available in several hole patterns for a full range of design needs, circuit speeds, component types and density. May be copper clad on one side. A complete line of accessory products also available, including eyelets, push-in (solderable or solderless), Wire- Wrap and screw machine terminals for all Vectorbord Prototyping Boards. Pattern H Pattern M Enlarged to show detail .05 .10 .05 .10 .023 .062 .027 .067 Pattern G Pattern P 0.1 0.1 0.2 .062 .040 .067 .044 0.1 0.1 Pattern Part No. Width Length Thick Hole Material/Description P 59P44-032 4.50 6.00 0.031 0.042 FR4 Epoxy Glass P 64P44WE 4.50 6.50 0.062 0.042 FR4 Epoxy Glass P 64P44XXXP 4.50 6.50 0.062 0.042 FR2 Phenolic P 64P44 4.50 6.50 0.062 0.042 CEM-1 Epoxy Glass Composite P 84P44WE 4.50 8.50 0.062 0.042 FR4 Epoxy Glass P 169P44C1 4.50 17.00 0.062 0.042 CEM-1, copper, 1 side P 169P44C2 4.50 17.00 0.062 0.042 CEM-1, copper, 2 sides P 169P44 4.50 17.00 0.062 0.042 CEM-1 P 169P44XXXP 4.50 17.00 0.062 0.042 FR2 Phenolic P 169P44WEC1 4.50 17.00 0.062 0.042 FR4 Epoxy Glass, copper, 1 side P 169P44WE 4.50 17.00 0.062 0.042 FR4 Epoxy Glass P 169P59-032 6.00 17.00 0.031 0.042 FR4 Epoxy Glass P 169P59C1 6.00 17.00 0.062 0.042 CEM-1, copper, 1 side. P 169P59XXXP 6.00 17.00 0.062 0.042 FR2 Phenolic P 169P79WE 8.00 17.00 0.062 0.042 FR4 Epoxy Glass P 169P79 8.00 17.00 0.062 0.042 CEM-1 P 169P84 8.50 17.00 0.062 0.042 CEM-1 P 169P84C1 8.50 17.00 0.062 0.042 CEM-1, copper, 1 side P 169P84WE 8.50 17.00 0.062 0.042 FR4 Epoxy Glass P 169P84WEC1 8.50 17.00 0.062 0.042 FR4, copper 1 side P 349P84 8.50 35.00 0.062 0.042 CEM-1 P 169P99 10.00 17.00 0.062 0.042 CEM-1 G 42G22WEC1 4.50 8.50 0.062 0.062 CEM-1, copper 1 side G 42G24WE 4.80 8.50 0.062 0.062 CEM-1 G 85G24WE 4.80 17.00 0.062 0.062 CEM-1 G 85G42WE 8.50 17.00 0.062 0.062 FR4 Epoxy Glass H 85H48WE 4.80 8.50 0.062 0.062 FR4 Epoxy Glass H 170H48WE 4.80 17.00 0.062 0.062 FR4 Epoxy Glass H 85H85WE 8.50 8.50 0.062 0.062 FR4 Epoxy Glass H 170H85WE 8.50 17.00 0.062 0.062 FR4 Epoxy Glass M 126M76-032 4.00 6.50 0.037 0.025 FR4 Epoxy Glass M 336M76-032 4.00 17.00 0.037 0.025 FR4 Epoxy Glass M 336M76-032C1 4.00 17.00 0.037 0.025 FR4 Epoxy Glass, copper 1 side 11115 Vanowen St., North Hollywood, CA 91605 Phone(818)985-8208 Fax(818)985-7708 Vectorbord is a registered trademark of Toll-Free (800) 423-5659 Web site: Board Patterns Prototyping Boards Voltage/Ground Plane Zig-Zag Buses Interleaved Bus Pattern Pattern Pattern on one side alternates holes Overall voltage and ground planes Two independent copper buses that on opposite board sides with opposite side bus run the full width of board Isolated copper plated thru holes with (See illustration) 0.3 DIPs span buses insulating ring 3-hole pads provide holes for DIP s All copper buses are solder plated Can be committed to either voltage 0.3 wide DIP s span buses Accepts solder or wire-wrap or ground plane with solder washers and are soldered + pads terminals (T124) Accepts wire-wrap or solder (see Parts & Accessories Section) Good for Vcc & Gnd distribution & terminals in Zig-Zag bus noise immunity Universal & Peripheral 3-Hole Solder Pad Pattern Bus Pattern 02 Pad-Per-Hole and Pad-Per- Hole Voltage and ground buses Voltage and Ground bus lines trace a and Ground Plane Patterns interleaved between pad areas path around board perimeter Sockets (DIP) and components Some boards have back to back Isolated solder pads around all mount over bus lines for maximum peripheral buses holes for mounting of DIP s and component capacity Unrestricted pattern inside of buses other components Pattern provides for convenient (No copper geometry) Solder plated pad and bus sur soldered jumper wire connections faces to component leads or sockets General purpose and bus specific Board Dimensions All board dims are Height x Width applications Wire-wrap socket pins and w connectors available separately H Wire-Wrap is a trademark of Cooper Group Specifications subject to change without notice. ELECTRONIC COMPANY General Proto Products
