8 6 5 4 2 1 7 3 REVISIONS ZONE REV. DESCRIPTION APPROVED DATE ALL A TABLE REDRAWN ECO 3290 12/10/86 DETAIL 1 B REMOVED UNUSED P/N 02/10/09 C ADDED TS209N 03/04/11 D D ADDED TS-425 09/13/12 D DETAIL A 1.000 SCALE 2 : 1 .180 .100.010 A .291 +.015 .115 -.000 DETAIL 2 .210 C C 1.000 A .500 .281 .093 1.000 2 PL. 2.000 .291 A B B DETAIL 3 1.000 1.000 .291 A 11115 VANOWEN ST., NAME DATE UNLESS OTHERWISE SPECIFIED: NORTH HOLLYWOOD, CA 91605 DIMENSIONS ARE IN INCHES DRAWN TRUSHAR 02/06/09 TOLERANCES: A A CHECKED FRACTIONAL T-STRUT ANGULAR: 1 5. DEGREASE ENG APPR. TWO PLACE DECIMAL .03 4. STRAIGHT WITHIN .015/10 IN LENGTH THREE PLACE DECIMAL .010 MFG APPR. W/O INSERTS PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC 3. CUT ENDS TO BE SQUARE WITHIN .0025/INCH IN WIDTH Q.A. TOLERANCING PER: THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. REV 2. REMOVE ALL BURRS DRAWING IS THE SOLE PROPERTY OF THIRD ANGLE PROJECTION VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL 1 1. MAT L: AL. EXTRUSION, 6063-T6, PRE-ANOD., P/N TS100 REPRODUCTION IN PART OR AS A WHOLE B 5280006 D WITHOUT THE WRITTEN PERMISSION OF FINISH VECTOR ELECTRONICS & TECH., INC. IS NOTES: UNLESS OTHERWISE SPECIFIED. SCALE: 1:1 WEIGHT: SHEET 1 OF 1 PROHIBITED. DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 6 5 4 2 1 7 3 REVISIONS ZONE REV. DESCRIPTION APPROVED DATE RELEASED FOR PROTOTYPE ALL 100 UNITS OF CCK13S 02/14/80 - 50 CCM14S & 50 CCK13S P/N TS81-5 NO. OF HOLES WAS 30 A1 ACTUAL STOCK PARTS HAVE 31 07/31/80 P/N TS81-5 DIM. WAS 7.500 B 03/26/81 D D NO. OF HOLES WERE 31/ ECO2013 MOVED 1.000 DIM. LOCATION C CALLOUT FOR CLARITY NO ECO D ADDED TS81-6 &-7 D INC ECO 2628 12/17/84 A E INC ECO 3924 REMOVED P/N TS81-6, -7 F 02/10/09 TS169-5,TS209-5 B .002 C G ADDED P/N TS169-5/90 02/13/13 .500.015 .250 TYP250.002 TYP156 .060 +.030/-.000 4 6 E 7 C C 1.000.015 .291.008 REF. 1.000.060 TYP. DETAIL E SCALE 2 : 1 +.015 B B .115 -.000 .180 .100.010 .210 11115 VANOWEN ST., NAME DATE UNLESS OTHERWISE SPECIFIED: NORTH HOLLYWOOD, CA 91605 DIMENSIONS ARE IN INCHES 7. TOOLING MARK MAY APPEAR DRAWN TRUSHAR 02/10/09 TOLERANCES: A A C 6. USE .1565 DIA. PUNCH TO FORM RADIUS EQUAL WITHIN .005 FROM OF SLOT CHECKED L FRACTIONAL ANGULAR: .X 5. PART TO BE FREE OF BURRS AND SURFACE SCRATCHES T-STRUT ENG APPR. TWO PLACE DECIMAL .03 4. NON CUMULATIVE TOLERANCE THREE PLACE DECIMAL .005 MFG APPR. FOR SNAP-IN CARD GUIDE PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC 3. PART TO BE STRAIGHT WITHIN .015/10 INCHES IN LENGTH Q.A. TOLERANCING PER: THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. REV 2. CUT ENDS TO BE SQUARE WITHIN .0025/INCH IN WIDTH DRAWING IS THE SOLE PROPERTY OF THIRD ANGLE PROJECTION VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL 1 1. MAT L: AL. EXTRUSION, 6063-T6, PRE-ANOD., P/N TS100 REPRODUCTION IN PART OR AS A WHOLE B M6336D4.2 G WITHOUT THE WRITTEN PERMISSION OF FINISH VECTOR ELECTRONICS & TECH., INC. IS NOTES: UNLESS OTHERWISE SPECIFIED. SCALE: 1:1 WEIGHT: SHEET 1 OF 1 PROHIBITED. DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1
