CATALOG 128 CATALOG 128.qxd 4/24/2014 9:54 AM Page 18 Vectorbord Backplanes VME J1 or J2 J1 Backplanes - 3U Vector VME backplanes for J1 and J2 are 3U backplanes available in sizes from 3 to 21-slot. All boards are constructed from FR4 Epoxy Glass, and are assem- bled and tested. Press fit connec- tors are used throughout on all sizes. Front view of model VMEBP21J1 Power bug option on 21-slot J1 or J2 only. 10-Pin Power Bug (2.5 amps/pin) Rear view of model VMEBP21J1 Vector J1 Backplanes handle high signal densities and circuit speeds with integrity and reliability. Six-layer construction and controlled impedance design effectively reduce crosstalk and ringing on bus lines. Massive copper-clad power and ground planes on opposite board sides patented shielding technique effectively surrounds each signal trace with a closed conduc- tive loop for blocking both capacitive and inductive coupling. Front View of Model VMEBP8J1 Power symbols indicate position and values of voltage and ground on a typical J1 VME backplane 18 Specification subject to change without notice www.vectorelect.com 800-423-5659 BackplanesBackplanes CATALOG 128 CATALOG 128.qxd 4/24/2014 9:54 AM Page 19 Vectorbord Backplanes VME J1 or J2 Standard Features Layer Designation - J1 96-pin female connectors designed to DIN 41612, Class II specification +5V COMP Layer 1 and ground access through Mate-N-Lock connectors, mating connector hous- POWER Layer 2 ings and pins provided. Terminator modules included with J1 or J2. Standard INSULATION 0.80 connector spacing GROUND Layer 3 Extensive labeling on board surface identifies user assignable pins, IACK POWER Layer 4 and IACK OUT pins, and other information INSULATION Material: FR4 Epoxy Glass GND/+5SBY Layer 5 Thickness 0.125 .009 tm SOLDER Layer 6 Use VectorPak CCA160-3U Subrack for J1 or J2 Backplanes. Backplane Mounting Hardware Each Set includes: 0 )/ 7 M2.5 X 12MM Screw Mating connectors : 6+(5 3 Lockwasher 635,1* and crimp pins /2&. : 6+(5 M2.5 (DIN 125) Flat Washer included. HD56-1 42 sets VME J1 and J2 0 PP 3 1 +( 6&5(: HD56 12 sets 5.12 (3U) H Terminator Boards Ordering Information A pair of Terminator boards are included with each J1 and J2 backplane A Slots Length (Width) and are also available separately. There are two versions: Perpendicular Part No. 2 1.33 (33mm) VMEBP2J1 (standard) and parallel. The latter offers a lower profile (Normal profile: 6 4.74 (120mm) VMEBP6J1 1.0 parallels: .5) than the perpendicular, if this is needed. 8 6.34 (161mm) VMEBP8J1 9 7.14 (181mm) VMEBP9J1 10 7.94 (201mm) VMEBP10J1 21 16.74 (425mm) VMEBP21J1 2 1.33 (33mm) VMEBP2J2 Model VMETBJ1-P Model VMETBJ1 5 3.94 (100mm) VMEBP5J2 VMEBP6J2 6 4.74 (120mm) Part No. Description Height Width Thickness 5.54 (140mm) VMEBP7J2 7 8 6.34 (161mm) VMEBP8J2 VMETBJ1 J1, perpendicular 3.70 (94mm) 1.325 (34mm) .520 (13.2mm) 9 7.14 (181mm) VMETBJ2 J2, perpendicular 1.325 (34mm) VMEBP9J2 3.70 (94mm) .520 (13.2mm) VMETBJ1-P J1, parallel 3.70 (94mm) 1.00 (25.4mm) .520 (13.2mm) 10 7.94 (201mm) VMEBP10J2 J2, parallel VMETBJ2-P 3.70 (94mm) 1.00 (25.4mm) .520 (13.2mm) VMEBP21J2 21 16.74 (425mm) Power symbols indicate position and values of voltage and ground on a typical J2 VME backplane J2 Backplanes - 3U Vector J2 Backplanes are available in many sizes, corresponding to available Vector J1 backplanes. Featuring off-board termination using VMETBJ2 terminator modules. Pressfit 96-pin DIN connector pins are configured according to VME specifications connector row B is bussed for 32-bit expansion A and C rows can be used for local extension buses, such as VMX or VSB, or can be assigned according to user I/O requirements. 19 www.v ect or elect.com 800-423-5659