8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 RELEASED PER E050348 PEI 11/15/05 ECF F F 2 REVISED PER E091652 JS 09/11/09 REJH 30 DRILL THRU SEE NOTE 6 ( .1285 ) 3 REDRAWN PER E100871 DCS 6/29/10 KUK (6) PL. E E 2.22 2.000 D D .100 TYP .910 SEE NOTE 5 1.800 .11 .50 3.600 4.600 C C .90 -A- .005 .010 B B MATL TO BE .190 .100 REMOVED SWD DRAWN DATE VICOR NOTES: D.P. KELLY 05/97 1. MATERIAL EXTRUSION SEE SHEET 2 OF 2. UNLESS OTHERWISE SPECIFIED MATERIAL 2. REMOVE ALL BURRS AND SHARP EDGES. HS CFG, .90H, X-FLOW, DIMENSIONS ARE INCH MM TOLERANCES ARE: SEE NOTES 3. CLEAR FINISH, RoHS COMPLIANT PER CST-0001 LATEST REVISION. DECIMALS ANGLES LOW FLOW, THRU HOLE A A X.XX X.X = 0.01 0.25 1 4. DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV 5. DIMENSIONS APPLIES AT SURFACE -A- (2) PL. FINISH THIRD ANGLE PROJECTION 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (60 PL. SEE NOTES C 67131 30723 3 7. DIMENSIONS ARE INCHES ONLY. SCALE 2 : 1 SHEET 1 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 DRAWN FOR DEVELOPMENT XXX MM/YY XXX F F 3 E E 1.5 EACH SIDE OF VERT SEE DETAIL A A 1.756 R.018 .024 (2) PL. R.035 .910 .034 .215 .200 D D .035 .110 R.010 .040 * .086 R.035 (2) PL. (10) PL. (30) PL080 (14) PL. R.030 * 1.408 * .212 * .084 (32) PL748 (2) PL. (12) PL. (6) PL. * .217 (3) PL187 +.020 C .017 C 4.600 -.000 (2) PL. C L * .086 DETAIL A SCALE 4 : 1 B PROFILE COMMON B FOR 30196 30723 NOTES: SWD 1. MATL ALUMINUM 6063-T5 DRAWN DATE VICOR 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. JSARIPELLA 09/11/09 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. UNLESS OTHERWISE SPECIFIED MATERIAL HS CFG, .90H, X-FLOW, LOW DIMENSIONS ARE INCH MM 5. WORKMANSHIP STANDARDS WS-0004, WS-0006, AND WS-0007 APPLY TO THIS PART. TOLERANCES ARE: SEE NOTES DECIMALS ANGLES 6. DIMENSIONS ARE INCHES ONLY. FLOW, THRU HOLE, EXTRUSION A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30723 3 SCALE 2 : 1 SHEET 2 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1