8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053488 PEI 01/04/06 ECF F F 2 08/19/09 REJH DOCUMENT REVISED PER E091418 JS 3 REDRAWN PER E100902 DCS 7/14/10 KUK 4-40 UNC-2B COLD FORM TAP .120 DP MIN. FROM FAR SIDE DO NOT BREAK THRU E E (6) PL. 1.47 1.270 D D .100.010 .410 .650 .49 1.300 2.280 C C .40 .005 .010 .190 .100 MATL TO BE REMOVED B B SWD DRAWN DATE VICOR NOTES: P.E. IENI 12/01/05 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. 2. REMOVE ALL BURRS AND SHARP EDGES. UNLESS OTHERWISE SPECIFIED MATERIAL HS CFG X-FLOW, .4H DIMENSIONS ARE INCH MM 3. CLEAR FINISH, RoHS COMPLIANT, CHROMIUM FREE PER CST-0001 LATEST REVISION. TOLERANCES ARE: SEE NOTES DECIMALS ANGLES LOW FLOW, THREADED A 4. DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 5. DIMENSIONS ARE INCHES ONLY. SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 32173 3 SCALE 2 : 1 SHEET 1 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F 3 E E 1.5 EACH SIDE OF VERT R.035 (24) PL014 1.756 (2) PL. SEE DETAIL A R.035 R.018 .023 (2) PL410 .036 D D .235 .200 .110 .040 .031 .080 R.010 * .056 * .058 (4) PL. (2) PL. (8) PL252 R.030 * .138 * .133 (8) PL. (5) PL. (6) PL. * .060 * .297 (2) PL. +.020 2.280 -.000 C C * .030 * .060 DETAIL A SCALE 8 : 1 TYP PROFILE COMMON FOR 30722 B B 32173 30721 30184 SWD DRAWN DATE VICOR NOTES: JSARIPELLA 08/19/09 1. MATL: ALUMINUM 6063-T5 UNLESS OTHERWISE SPECIFIED 2. *DENOTES DIMENSIONS TO THEORETICAL SHARP CORNER MATERIAL HS CFG X-FLOW, .4H DIMENSIONS ARE INCH MM 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. TOLERANCES ARE: SEE NOTES LOW FLOW, THREADED, DECIMALS ANGLES A 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 EXTRUSION 5. WORKMANSHIP STANDARDS WS-0004, WS-0006 AND WS-0007 APPLY TO THIS PART. SIZE CAGE CODE DWG NO REV 6. DIMENSIONS ARE INCHES ONLY. FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 32173 3 SCALE 4 : 1 SHEET 2 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1