IB050Q096T70N1-00 Vicor

End of Life IBC Module IB0xxQ096T70xx-xx S CUNRTL S C US 5:1 Intermediate Bus Converter Module: Up to 750W Output Features & Benefits Input: 36 60V Low profile: 0.42 height above DC (38 55V for IB048x) board DC Output: 9.6V at 48V Industry standard 1/4 Brick pinout DC IN Output current up to 70A Sine Amplitude Converter (SAC) Size: Output power: up to 750W * Low noise 1MHz ZVS/ZCS 2.30 x 1.45 x 0.42in 2250V isolation 58.4 x 36.8 x 10.6mm DC (1500V isolation for IB048x) DC 98.2% peak efficiency * Lower power model available Product Description The Intermediate Bus Converter (IBC) Module is a very efficient, low prolfi e, Typical Applications isolated, fixed ratio converter for power system applications in enterprise and optical access networks. Enterprise networks Rated at up to 530W from 38V and up to 750W from 55V , the IBC conforms IN IN Optical access networks to an industry standard quarter-brick footprint while supplying power greatly exceeding competitive quarter-bricks. Its leading efficiency enables full load operation Storage networks at 50C with only 400LFM airflow. Its small cross section facilitates unimpeded airflow Automated test equipment above and below its thin body to minimize the temperature rise of downstream components. A baseplate option is available for alternative cooling schemes. Part Ordering Information Product Input Output Voltage Temperature Output Enable Package Pin Length Options Function Voltage (Nom.) x 10 Grade Current Logic I B 0 x x Q 0 9 6 T 7 0 x x x x IB = Intermediate Q = Quarter Brick 00 = Open frame T = -40C T +100C N = Negative OPERATING Bus Converter Format -40C T +125C P = Positive BP = Baseplate STORAGE 1 = 0.145 096 = (V nominal V = 48V x 10 048 = 38 55V OUT IN DC 70 = Max Rated Output Current DC 2 = 0.210 (5:1 transfer ratio) 050 = 36 60V DC 3 = 0.180 054 = 36 60V * DC * Operating transient to 75V DC IBC Module Rev 1.2 vicorpower.com Page 1 of 18 09/2016 800 927.9474End of Life IB0xxQ096T70xx-xx Absolute Maximum Ratings The absolute maximum ratings below are stress ratings only. Operation at or beyond these maximum ratings can cause permanent damage to the device. Parameter Comments Min Max Unit Input voltage (+IN to IN) See Input Range Specific Characteristics for details -0.5 75 V DC Input voltage slew rate 5 V / s EN to IN -0.5 20 V DC Output voltage (+OUT to OUT) See OVP setpoint max -0.5 (see note) V DC Output current P 750W 70 A OUT Dielectric withstand 2250 Input to output 1min 1500 for IB048x V DC 707 Output to baseplate 1min Temperature -40 Operating junction Hottest semiconductor 125 -40 Operating baseplate 100 C -55 Storage 125 Electrical Specifications Specifications valid at 48V , 100% rated load and 25C ambient, unless otherwise indicated. IN A t t rib u t e Symbol Conditions / Notes Min Typ Max Unit Input Range Specific Characteristics Part Number IB048Q096T70xx-xx Operating input voltage 38 48 55 V DC Non-operating input surge withstand < 100ms 75 V DC Operating input dV / dt 0.003 5 V / s Undervoltage protection Turnon 33 38 V DC Turnoff 31 36 V DC Turnon / turnoff hysteresis 2 V DC Time constant 7 s Undervoltage blanking time UV blanking time is enabled after start up 50 100 200 s Overvoltage protection Turnoff 60 64 V DC Turnon 55 64 V DC Time constant 4 s DC output voltage band No load, over V range 7.6 9.6 11.0 V IN DC Output OVP set point Module will shut down 12.0 12.8 V DC Input to output and input to baseplate 1min 1500 Dielctric withstand V DC Output to baseplate 707 Insulation resistance Input to output 30 M IBC Module Rev 1.2 vicorpower.com Page 2 of 18 09/2016 800 927.9474