515D338M016EK6AE3 Vishay

Not for New Designs 515D www.vishay.com Vishay Sprague Aluminum Capacitors +85 C, Miniature, Radial Lead FEATURES High CV per case size Low cost Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 QUICK REFERENCE DATA RIPPLE CURRENT MULTIPLIERS TEMPERATURE DESCRIPTION VALUE AMBIENT TEMPERATURE MULTIPLIERS Nominal case size 0.197 x 0.433 5.0 x 11.0 D x L in mm to 0.709 x 1.575 18.0 x 40.0 +70 C 1.27 +85 C 1.0 -40 C to +85 C Operating temperature -25 C to +85 C for 315 WV FREQUENCY (Hz) DC to 450 WV units DC CAP. 50 TO 100 TO 300 TO WV 1 kHz 10 kHz DC (F) 60 120 400 Rated capacitance range, C 0.1 F to 18 000 F R 0 to 47 0.75 1 1.35 1.57 2.00 Tolerance on C 20 % R 6.3 to 100 100 to 470 0.80 1 1.23 1.34 1.50 Rated voltage range, U 6.3 WV to 450 WV R DC DC 1000 to 18 000 0.85 1 1.10 1.13 1.15 Termination 2 radial leads 160 to 450 0.47 to 220 0.80 1 1.25 1.40 1.60 2000 h: CAP 20 % from initial measurement. Life validation test at 85 C DF 2 x initial specified limit. LOW TEMPERATURE PERFORMANCE DCL initial specified limit. (T) (+20 C) MAXIMUM IMPEDANCE RATIO Z / Z 1000 h: CAP 20 % from initial MAXIMUM AT 120 Hz measurement. RATED VOLTAGE Shelf life at 85 C Z - 25 C / Z + 20 C Z - 40 C / Z + 20 C DF 2 x initial specified limit. (WV ) DC DCL initial specified limit. 6.3 4.0 10.0 Rated voltage for 1 and 2 min for 10.0 3.0 8.0 6.3 WV to 100 WV units: DC DC 16.0 2.0 6.0 I < 0.03 CV or 4 A (whichever is greater). 25.0 2.0 4.0 I < 0.04 CV or 3 A 35.0 to 100.0 2.0 3.0 DC leakage current (whichever is greater). Rated voltage for 1 min for 160.0 to 200.0 3.0 4.0 160 WV to 450 WV units: DC DC 250.0 3.0 6.0 I < 0.1 CV + 40 A and 315.0 to 400.0 6.0 - CV 1000 I < 0.04 CV + 100 A and CV > 1000 450.0 15.0 - DIMENSIONS in inches millimeters CASE NOMINAL CASE SIZE LEAD SPACING NOMINAL LEAD DIAMETER TYPICAL WEIGHT CODE D x L S D (g) JA 0.197 x 0.433 5.0 x 11.0 0.079 2.0 0.020 0.50 0.44 AA 0.248 x 0.433 6.3 x 11.0 0.098 2.5 0.020 0.50 0.60 BB 0.315 x 0.453 8.0 x 11.5 0.138 3.5 0.024 0.60 0.95 CC 0.394 x 0.492 10.0 x 12.5 0.197 5.0 0.024 0.60 1.48 CD 0.394 x 0.630 10.0 x 16.0 0.197 5.0 0.024 0.60 1.75 CG 0.394 x 0.787 10.0 x 20.0 0.197 5.0 0.024 0.60 2.37 Revision: 04-May-2018 Document Number: 42052 1 For technical questions, contact: aluminumcaps4 vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000Not for New Designs 515D www.vishay.com Vishay Sprague DIMENSIONS in inches millimeters CASE NOMINAL CASE SIZE LEAD SPACING NOMINAL LEAD DIAMETER TYPICAL WEIGHT CODE D x L S D (g) DG 0.492 x 0.787 12.5 x 20.0 0.197 5.0 0.024 0.60 3.73 DK 0.492 x 0.984 12.5 x 25.0 0.197 5.0 0.024 0.60 4.85 EK 0.630 x 0.984 16.0 x 25.0 0.295 7.5 0.031 0.80 7.08 EN 0.630 x 1.240 16.0 x 31.5 0.295 7.5 0.031 0.80 8.94 ER 0.630 x 1.398 16.0 x 35.5 0.295 7.5 0.031 0.80 10.50 FR 0.709 x 1.398 18.0 x 35.5 0.295 7.5 0.031 0.80 12.53 FV 0.709 x 1.575 18.0 x 40.0 0.295 7.5 0.031 0.80 15.71 ELECTROLYTIC CAPACITOR WITH CUT OR FORMED LEADS in inches millimeters 0.177 Code S Code F Code S 0.177 4.5 4.5 0.177 X X 4.5 0.197 0.20 (1) 0.197 0.20 0.197 0.20 (1) F (1) D 5.0 0.5 D F D F 5.0 0.5 5.0 0.5 (2) d (2) (2) d d 0.177 Code C Code S Code S 4.5 0.033 0.006 0.039 0.008 D S 0.20 0.5 0.85 0.15 1.0 0.2 (2) d (4, 5, 6.3, 8) (10, 12.5, 16, 18) DIMENSIONS in inches millimeters DIMENSIONS FORMING FORMED (3) METHOD LEAD CODE DL.S. P e X (Max.) 0.197 5.0 0.197 5.0 0.079 2.0 - 0.059 1.5 Formed and cut F 0.248 6.3 0.197 5.0 0.098 2.5 - 0.098 2.5 0.315 8.0 0.197 5.0 0.138 3.5 - 0.098 2.5 0.394 10.0 0.197 5.0 - - - 0.492 12.5 0.197 5.0 - - - Cut C 0.630 16.0 0.295 7.5 - - - 0.709 18.0 0.295 7.5 - - - 0.197 5.0 0.197 5.0 0.079 2.0 0.043 1.1 0.059 1.5 0.248 6.3 0.197 5.0 0.098 2.5 0.043 1.1 0.059 1.5 0.315 8.0 0.197 5.0 0.138 3.5 0.051 1.3 0.059 1.5 Snap-in S 0.394 10.0 0.197 5.0 - 0.051 1.3 - 0.492 12.5 0.197 5.0 - 0.051 1.3 - 0.630 16.0 0.295 7.5 - 0.051 1.3 - 0.709 18.0 0.295 7.5 - 0.051 1.3 - Notes th Coding of cut or formed lead to be added to the end of type number in 15 position (with position 14 coded 6) (1) Formed lead (2) Lead thickness d depends on capacitor specification (3) Lead protrusion at bottom of tape Revision: 04-May-2018 Document Number: 42052 2 For technical questions, contact: aluminumcaps4 vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000