Type 225P Vishay Sprague Polyester Capacitors Filmite E, ORANGE DROP , Radial Lead FEATURES Utilizes minimum area where printed wiring board space is most important Wound from PETP polyester film and thin gauge RoHS foil under carefully controlled atmospheric COMPLIANT conditions Protected against moisture by a conformal coating of epoxy Specifically designed for printed wiring board applications Widely used in computers, instrumentation and telecommunications equipment 100 VDC through 600 VDC, may be operated up to + 125 C with proper dearting PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 85 C Dielectric Withstanding Voltage: To + 105 C when working voltage is reduced to 70 % of Capacitors shall withstand a DC potential of 250 % of rated + 85 C rating to + 125 C when working voltage is reduced voltage applied between terminals for not more than 5 to 50 % of 85 C rating seconds. The test voltage must be applied and discharged through a resistor of 1 ohm per volt. Insulation Resistance: After a 2 minute charge at rated voltage or 500 V, whichever is less. Humidity Test: Condition capacitors with no voltage applied for 72 hours at At + 25 C: 100 000 Megohm for C 0.25 Microfarads 95 % relative humidity and + 75 C. Remove capacitors from 25000 Megohm - Microfarads for C > 0.25 Microfarads humidity chamber, wipe surface dry of moisture and dry in At + 85 C: 10 000 Megohm for C 0.15 Microfarads circulating air for 4 hours. Measure insulation resistance after 1500 Megohm - Microfarads for C > 0.15 Microfarads a 2 minute charge at 25 C and rated voltage or 500 VDC, At + 105 C: 1500 Megohm for C 0.17 Microfarads whichever is less. Minimum product of insulation resistance 250 Megohm - Microfarads for C > 0.17 Microfarads and capacitance shall be 5000 Megohm - Microfarads after At + 125 C: 200 Megohm for C 0.13 Microfarads test but need not exceed 10 000 Megohm. Not more than 25 Megohm - Microfarads for C > 0.13 Microfarads one failure allowed in 12 units tested. Capacitance Tolerance and Dissipation Factor: DC Life Test: Capacitors shall be measured at a frequency of 1000 Hz at Capacitance are capable of withstanding a 500 hour life test + 25 C or else be referred to measurements made at that at + 85 C at 150 % of rated working voltage. After test, frequency and temperature. The maximum dissipation factor capacitance shall not have changed by more than 5 % of shall be 0.75 % initial value, insulation resistance shall not have decreased by more than 50 % of the initial limit and dissipation factor shall not have increased to more than 1 %. DIMENSIONS in inches millimeters L L L T Max. Max. Max. Max. H Max. 0.237 0.237 6.020 0.237 6.020 6.020 Max. Max. Max. Lead Lead Lead Length Length Length Tinned Copper-Clad Steel 0.032 0.813 Dia. (No. 20 AWG) S S S 0.030 0.762 0.060 1.524 0.030 0.762 Terminal A Terminal B Terminal D S CASE L CODE (Max.) Terminal A and B Terminal D W 0.70 17.78 0.562 14.275 0.375 9.525 X 0.80 20.32 0.613 15.570 0.375 9.525 Y 1.25 31.75 0.969 24.613 0.719 18.263 Document Number: 42016 For technical questions, contact: spresale vishay.com www.vishay.com Revision: 19-Feb-07 25Type 225P Polyester Capacitors Vishay Sprague Filmite E, ORANGE DROP , Radial Lead CAPACITANCE CHANGE DISSIPATION FACTOR VS.TEMPERATURE 1.5 16 14 12 10 CAPACITANCE CHANGE ENVELOPE 1.0 8 FOR 96 % CONFIDENCE LEVEL 6 TYPICAL 4 2 0.5 0 2 4 0 6 - 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125 - 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125 - 50 + 100 - 50 + 100 TEMPERATURE DEG. CENTIGRADE TEMPERATURE DEG. CENTIGRADE STANDARD RATINGS* F SIZE 10 % TOLERANCE PART NUMBER LHT 100 VDC/70 VAC** 0.001 225P10291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0012 225P12291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0015 225P15291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0018 225P18291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0022 225P22291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0027 225P27291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0033 225P33291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0039 225P39291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0047 225P47291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0056 225P56291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0068 225P68291W 0.70 17.78 0.35 8.89 0.25 6.35 0.0082 225P82291W 0.70 17.78 0.35 8.89 0.25 6.35 0.01 225P10391W 0.70 17.78 0.35 8.89 0.25 6.35 0.012 225P12391W 0.70 17.78 0.35 8.89 0.25 6.35 0.015 225P15391W 0.70 17.78 0.35 8.89 0.25 6.35 0.018 225P18391W 0.70 17.78 0.35 8.89 0.25 6.35 0.022 225P22391W 0.70 17.78 0.35 8.89 0.25 6.35 0.027 225P27391W 0.70 17.78 0.37 9.40 0.27 6.86 0.033 225P33391W 0.70 17.78 0.37 9.40 0.27 6.86 0.039 225P39391W 0.70 17.78 0.42 10.67 0.30 7.62 0.047 225P47391W 0.70 17.78 0.42 10.67 0.30 7.62 0.056 225P56391W 0.70 17.78 0.49 12.45 0.34 8.64 0.068 225P68391W 0.70 17.78 0.49 12.45 0.34 8.64 0.082 225P82391W 0.70 17.78 0.55 13.97 0.40 10.16 0.1 225P10491W 0.70 17.78 0.55 13.97 0.40 10.16 0.12 225P12491X 0.80 20.32 0.57 14.48 0.37 9.40 0.15 225P15491X 0.80 20.32 0.62 15.75 0.40 10.16 0.18 225P18491X 0.80 20.32 0.66 16.76 0.43 10.92 0.22 225P22491X 0.80 20.32 0.70 17.78 0.46 11.68 0.27 225P27491X 0.80 20.32 0.74 18.80 0.49 12.45 0.33 225P33491X 0.80 20.32 0.77 19.56 0.52 13.21 0.39 225P39491X 0.80 20.32 0.81 20.57 0.55 13.97 0.47 225P47491X 0.80 20.32 0.86 21.84 0.60 15.24 0.56 225P56491Y 1.25 31.75 0.88 22.35 0.55 13.97 0.68 225P68491Y 1.25 31.75 0.90 22.86 0.58 14.73 0.82 225P82491Y 1.25 31.75 0.94 23.88 0.65 16.51 1.0 225P10591Y 1.25 31.75 0.98 24.89 0.72 18.29 * Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague Distribution Network. For complete Part Number, add letter and number for terminal and lead length. See Ordering Information (Ex: 225P39391WD3). ** 60 Hz rms www.vishay.com For technical questions, contact: spresale vishay.com Document Number: 42016 26 Revision: 19-Feb-07 CAPACITANCE CHANGE/1000 Hz % % DISSIPATION/1000 Hz