CRCW010056K0FREL Vishay

CRCW01005 e3 www.vishay.com Vishay Standard Thick Film Chip Resistors FEATURES Very small standard size (0.4 mm x 0.2 mm) Low tolerance (1 %) Material categorization: For definitions of compliance please see www.vishay.com/doc 99912 STANDARD ELECTRICAL SPECIFICATIONS LIMITING ELEMENT CASE CASE POWER RATING TEMPERATURE RESISTANCE VOLTAGE TOLERANCE TYPE SIZE SIZE P COEFFICIENT RANGE SERIES 70 U % max. IMPERIAL METRIC W ppm/K AC /DC RMS V 1 E24 E96 250 10.0 to 1M 2, 5 E24 0.031 15 CRCW01005 01005 RR0402M 1 1.0 to 9.76 E24 E96 -200/+600 2, 5 1.0 to 9.1 E24 Zero-Ohm-Resistor: R = 50 m , I = 0.5 A max. max. Notes These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance vale drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS PARAMETER UNIT CRCW01005 (1) Rated Dissipation P W 0.031 70 Operating Voltage U AC /DC V 15 max. RMS Insulation Voltage U (1 min) V 30 ins 9 Insulation Resistance > 10 Operating Temperature Range C -55 to +125 Mass mg 0.07 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 125 C is not exceeded. Revision: 28-Oct-13 Document Number: 20056 1 For technical questions, contact: thickfilmchip vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 CRCW01005 e3 www.vishay.com Vishay PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRCW01001K00FREL C R C W 0 1 0 0 1 K 0 0 F R E L TYPE VALUE TOLERANCE TCR PACKAGING CRCW0100 R = Decimal F = 1.0 % R = 250 ppm/K EL K = Thousand G = 2.0 % Y = -200 ppm/K/+600 ppm/K M = Million J = 5.0 % 0 = Jumper 0000 = Jumper Z = Jumper PRODUCT DESCRIPTION: CRCW01005 250 1K0 1 % ET3 e3 CRCW01005 250 1K0 1 % ET3 e3 RESISTANCE TOLERANCE TYPE TCR PACKAGING LEAD (Pb)-FREE VALUE VALUE CRCW01005 250 ppm/K 1R0 = 1 1 % ET3 e3 = Pure tin -200/+600 ppm/K 2 % termination finish 10R = 10 5 % 1K0 = 1 k 10K = 10 k 1M0 = 1 M 0R0 = Jumper PACKAGING TYPE CODE QUANTITY CARRIER TAPE WIDTH PITCH REEL DIAMETER CRCW01005 EL = ET3 20 000 Paper tape acc. to IEC 60286-3, Type 1a 8 mm 2 mm 180 mm/7 DIMENSIONS in millimeters RECOMMENDED SOLDER PAD SIZE DIMENSIONS DIMENSIONS IMPERIAL METRIC L W H T1 T2 a b l 01005 RR0402M 0.4 0.02 0.2 0.02 0.13 0.02 0.10 0.03 0.10 0.03 0.15 0.2 0.2 Note No marking for 01005 size. DERATING 100 50 0 - 50 0 50 100 125 150 70 Ambient Temperature in C amb Revision: 28-Oct-13 Document Number: 20056 2 For technical questions, contact: thickfilmchip vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Fraction of Rated Dissipation P in % 70