LCF-102PTIFGDBN0H www.vishay.com Vishay 10.2 Color TFT Display FEATURES Type: TFT Diagonal dimension: 10.2 Display format: 800 x 480 (RGB) Built-in controller: RA8875 +3.3 V, +5 V power supply Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS ITEM DIMENSION UNIT STANDARD VALUE ITEM SYMBOL UNIT Dot matrix 800 x 480, RGB (TFT) dots MIN. TYP. MAX. Module dimension 235.0 x 145.8 x 12.1 mm Operating T -20 - +70 C OP temperature Active area 222.0 x 132.48 mm Storage Dot pitch 0.0925 x 0.276 mm T -30 - +80 C ST temperature TFT, normally white, LCD type Notes transmissive Device is subject to be damaged permanently if stresses beyond View direction 12 oclock those absolute maximum ratings listed above Gray scale inversion direction 6 oclock Temperature 60 C, 90 % RH max. temperature > 60 C, Backlight type LED, normally white absolute humidity shall be less than 90 % RH at 60 C Controller IC RA8875 Interface Digital 8080 family MPU Note Color tone changed by temperature and driving voltage ELECTRICAL CHARACTERISTICS STANDARD VALUE ITEM SYMBOL CONDITION UNIT MIN. TYP. MAX. Supply voltage for LCM V - 3.0 3.3 3.6 V DD (1) Supply current for LCM I - 190 195 mA DD (2)(3) Operation current for LED driver I V = +5 V 500 - 750 mA LED LED (2)(3) Power consumption V = +5 V 2500 - 3750 mW LED Supply voltage for LED driver V V -5 - V DD LED+ (3)(4)(5) LED life time t 20 000 - - h Notes (1) This value us test for V = 3.3 V, T = 25 C only DD amb (2) Base on V = 5 V for the backlight driver IC specification LED (3) T = 25 C amb (4) Brightness to be decreased to 50 % of the initial value (5) The single LED lamp case Revision: 30-Jun-17 Document Number: 37519 1 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 LCF-102PTIFGDBN0H www.vishay.com Vishay INTERFACE PIN FUNCTION PIN NO. SYMBOL FUNCTION 1 GND System ground pin of the IC connect to system ground 2V Power supply: +3.3 V DD 3 NC No connection 4 RS Data / command select 5 WR Write strobe signal 6 RD Read strobe signal 7DB0 Data bus 8DB1 Data bus 9DB2 Data bus 10 DB3 Data bus 11 DB4 Data bus 12 DB5 Data bus 13 DB6 Data bus 14 DB7 Data bus (1) 15 DB8 Data bus (when select 8 bits mode, this pin is no connection) (1) 16 DB9 Data bus (when select 8 bits mode, this pin is no connection) (1) 17 DB10 Data bus (when select 8 bits mode, this pin is no connection) (1) 18 DB11 Data bus (when select 8 bits mode, this pin is no connection) (1) 19 DB12 Data bus (when select 8 bits mode, this pin is no connection) (1) 20 DB13 Data bus (when select 8 bits mode, this pin is no connection) (1) 21 DB14 Data bus (when select 8 bits mode, this pin is no connection) (1) 22 DB15 Data bus (when select 8 bits mode, this pin is no connection) 23 WAIT Wait signal output (H: active) 24 NC No connection 25 CS Chip select 26 RST Hardware reset (2)(3) 27 L / R Left / right selection, default L / R = H (2)(3) 28 U / D Up / down selection, default U / D = L 29 NC No connection 30 NC No connection 31 NC No connection 32 NC No connection 33 VLED- Power for LED driver IC (ground) 34 VLED- Power for LED driver IC (ground) 35 VLED+ Power for LED driver IC (+5 V) 36 VLED+ Power for LED driver IC (+5 V) Notes (1) When select 8 bit mode, DB0 to DB7 be used, DB8 to DB15 no connection. When select 16 bit mode, DB8 to DB15 be used (2) Selection of scanning mode SETTING OF SCAN CONTROL INPUT SCANNING DIRECTION U / D L / R GND V Up to down, left to right DD V GND Down to up, right to left DD GND GND Up to down, right to left V V Down to up, left to right DD DD (3) Definition of scanning direction, refer to the figure as below: VISHAY LCD VISHAY LCD 1. U / D = L L / R = H 2. U / D = L L / R = L 3. U / D = H L / R = H 4. U / D = H L / R = L Revision: 30-Jun-17 Document Number: 37519 2 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 VISHAY LCD VISHAY LCD