RCWPM (Military M/D55342)
www.vishay.com
Vishay Dale
Thick Film Chip Resistors, Military / Established Reliability
MIL-PRF-55342 Qualified, Type RM
FEATURES
Fully conforms to the requirements of
MIL-PRF-55342
Established reliability - verified failure rate; M, P, R, U, S,
V, and T levels
Construction is sulfur impervious against a high sulfur
environment (ASTM B 809-95 test method)
100 % group A screening per MIL-PRF-55342
Termination style B - tin / lead wraparound over nickel
barrier
MATERIAL SPECIFICATIONS
Operating temperature range is -65 C to +150 C
Resistive element Ruthenium oxide
For MIL-PRF-32159 zero ohm jumpers, see Vishay Dales
Encapsulation Epoxy
RCWPM Jumper (Military M32159) datasheet
Substrate 96 % alumina
(www.vishay.com/doc?31028)
Termination Solder-coated nickel barrier
Material categorization: for definitions of compliance
Solder finish Tin / lead solder alloy
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
POWER MAX.
MIL RESISTANCE TEMPERATURE
VISHAY DALE MIL-PRF-55342 CASE RATING WORKING TOLERANCE
(2)
SPEC. TERM. RANGE COEFFICIENT
(1)
MODEL STYLE SIZE P VOLTAGE %
70 C
SHEET ppm/C
W V
1 to 9.1 2, 5, 10 200, 300
RCWPM-0502,
RM0502 01 B 0502 0.05 40 10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0502-98
10 to 10M 0.5 100, 200, 300
1 to 9.1 2, 5, 10 200, 300
RCWPM-550,
RM0505 02 B 0505 0.125 40 10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-550-98
10 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-5100,
RM1005 03 B 1005 0.20 75 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-5100-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-5150,
RM1505 04 B 1505 0.15 125 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-5150-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-7225,
RM2208 05 B 2208 0.225 175 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-7225-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-575,
(3)
RM0705 06 B 0705 0.15 50 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-575-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-1206,
RM1206 07 B 1206 0.25 100 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-1206-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-2010,
RM2010 08 B 2010 0.80 150 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-2010-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-2512,
RM2512 09 B 2512 1.0 200 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-2512-98
5.62 to 10M 0.5 100, 200, 300
1 to 5.1 2, 5, 10 200, 300
RCWPM-1100,
RM1010 10 B 1010 0.50 75 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-1100-98
5.62 to 10M 0.5 100, 200, 300
1 to 9.1 2, 5, 10 200, 300
RCWPM-0402,
RM0402 11 B 0402 0.05 30 10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0402-98
10 to 10M 0.5 100, 200, 300
Revision: 10-Mar-17 Document Number: 31010
1
For technical questions, contact: ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCWPM (Military M/D55342)
www.vishay.com
Vishay Dale
STANDARD ELECTRICAL SPECIFICATIONS
POWER MAX.
MIL RESISTANCE TEMPERATURE
VISHAY DALE MIL-PRF-55342 CASE RATING WORKING TOLERANCE
(2)
SPEC. TERM. RANGE COEFFICIENT
(1)
MODEL STYLE SIZE P VOLTAGE %
70 C
SHEET ppm/C
W V
1 to 5.1 2, 5, 10 200, 300
RCWPM-0603,
RM0603 12 B 0603 0.10 50 5.6 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0603-98
5.62 to 10M 0.5 100, 200, 300
1 to 9.1 2, 5, 10 200, 300
RCWPM-0302,
RM0302 13 B 0302 0.04 15 10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0302-98
10 to 10M 0.5 100, 200, 300
Notes
DSCC has created a series of drawings to support the need for 0201-sized product. Vishay Dale is listed as a resource on this drawing as
follows:
POWER RATING MAX. WORKING
DSCC DRAWING VISHAY DALE RES. RANGE RES. TOL. TEMP. COEF.
(1)
TERM. P VOLTAGE
70 C
NUMBER MODEL % ppm/C
W V
10 to 46.4 200
07009 RCWP-0201 B 0.05 1, 5 30
47 to 1M 100
This drawing can be viewed at: www.landandmaritime.dla.mil/Programs/MilSpec/ListDwgs.aspx?DocTYPE=DSCCdwg
(1)
Continuous working voltage shall be P x R or maximum working voltage, whichever is less
(2)
Characteristics: K = 100 ppm/C; L = 200 ppm/C; M = 300 ppm/C
(3)
MIL case size 0705 and EIA case size 0805 are dimensionally the same
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: M55342M02B10E0RWB (preferred part number format)
M 55342 M 0 2 B1 0 E 0 R W B
MIL SPEC. TERMINATION VALUE AND FAILURE
(1)
CHARACTERISTICS PACKAGING SPECIAL
STYLE SHEET STYLE TOLERANCE RATE
D55342 K = 100 ppm (see Standard B = pre-tinned (see Tolerance C = non-ER TP = tin / lead, Blank =
applies to L = 200 ppm Electrical nickel barrier, and Multipliers M = 1.0 %/1000 h T/R (full) standard
Style 07 M = 300 ppm Specifications wraparound table) P = 0.1 %/1000 h TN = tin / lead, (dash number)
(RM1206) table) R = 0.01 %/1000 h T/R (full), w/ESD (up to 1 digits)
(2)
only. U = 0.01 %/1000 h UL = tin / lead, T/R D = 0.5 %
(3)
S = 0.001 %/1000 h single lot date code tolerance
(2)
M55342 V = 0.001 %/1000 h S3 = tin / lead, S =
applies to T = space level T/R (1000 pieces) space level
all other SV = tin / lead, T/R w/option 1 part
(4)
styles. (1000 pieces), w/ESD marking (-97)
WB = tin / lead, T =
waffle tray space level (-98)
WA = tin / lead, 2 =
waffle tray, option 1
w/ESD part marking
(4)
WL = tin / lead, (-20)
waffle tray, 3 =
single lot date code oiptions 2 and 3
S2 = tin / lead, part marking
(4)
T/R (500 pieces) (-30)
SU = tin / lead, T/R
(500 pieces), w/ESD
S6 = tin / lead,
T/R (300 pieces)
ST = tin / lead, T/R
(300 pieces), w/ESD
Historical Part Numbering: M55342M02B10E0R (will continue to be accepted)
M55342 M 02 B 10E0 R WB
MIL TERMINATION VALUE AND FAILURE PACKAGING
CHARACTERISTICS SPEC. SHEET
STYLE STYLE TOLERANCE RATE CODE
Notes
For additional information on packaging, refer to the Surface Mount Resistor Packaging document (www.vishay.com/doc?31543)
(1)
Products with space level failure rates are only offered in packaging codes with ESD overpack and labeling. For all other failure rates, the
ESD pack codes are an optional type of packaging
(2)
Failure rates U and V require group A and B inspection ran on each production lot
(3)
Add a D after the packaging code at the end of the global part number to specify Vishay Dale Thick Film product with a tolerance of 0.5 %
(4)
MIL spec option 1, 2, and 3 part marking is not offered for the slash sheet 01, 02, 11, and 13 sizes
Revision: 10-Mar-17 Document Number: 31010
2
For technical questions, contact: ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000