Not for New Designs - Alternative Device: MKP385 MKP1837 www.vishay.com Vishay Roederstein Metallized Polypropylene Film Capacitor Radial AC and Pulse Capacitor FEATURES Mounting: radial Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS Oscillator, timing, and LC/RC filter circuits, high frequency coupling / decoupling, sample an d hold circuits. QUICK REFERENCE DATA Capacitance range 0.01 F to 0.1 F Capacitance tolerance 10 % (K) 5 % (J) 2.5 % (H) 1 % (F) Climatic testing class according to IEC 60068 55/100/56 Dielectric Polypropylene film Electrodes Vacuum deposited aluminum Construction Extended metallized film (refer to general information) Coating Flame retardant plastic case (UL-class 94 V-0), epoxy resin sealed Leads Tinned wire Marking Manufacturers logo, type, C-value, rated voltage, tolerance, date of manufacture Operating temperature range -55 C to +100 C Capacitance drift Up to +40 C, < 0.5 % for a period of two years Rated DC voltages (U ) 160 V R DC Permissible AC voltages (RMS) up to 60 Hz 100 V AC Test voltage (electrode/electrode) 1.6 x U for 2 s R Measured at 100 V after one minute DC Insulation resistance 100 000 M minimum value -6 Temperature coefficient -250 C x 10 /C (typical value) dV/dt = 390 V/s Maximum pulse rise time If the maximum pulse voltage is less than the rated voltage, higher dV/dt values can be permitted. At +85 C: U = 1.0 U C R Derating for DC and AC category voltage U C At +100 C: U = 0.7 U C R Self inductance ~ 6 nH measured with 2 mm long leads Pull test on leads 30 N in direction of leads according to IEC 60068-2-21 Dielectric absorption 0.05 % (typical value) according to IEC 60384-1 Operational life > 300 000 h Reliability Failure rate < 5 FIT (40 C and 0.5 x U ) R MEASURED AT C 0.1 F -3 1 kHz 0.4 x 10 -3 Dissipation factor tan 10 kHz 0.6 x 10 -3 100 kHz 4 x 10 Maximum values Note For further details, please refer to the general information available at www.vishay.com/doc 26033 Revision: 27-Sep-2021 Document Number: 26017 1 For technical questions, contact: dc-film vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000Not for New Designs - Alternative Device: MKP385 MKP1837 www.vishay.com Vishay Roederstein DIMENSIONS in millimeters W L max. max. Marking H max. 0.6 - 1 6.0 0.4 5.0 0.4 0.5 ELECTRICAL DATA DIMENSIONS VOLTAGE CAP. CAPACITANCE U V W x H x L RDC AC CODE (F) CODE (mm) 0.010 -310 5.5 x 7.0 x 7.5 0.015 -315 5.5 x 7.0 x 7.5 0.022 -322 5.5 x 7.0 x 7.5 160 16 0.033 -333 100 7.5 x 9.0 x 7.5 0.047 -347 7.5 x 9.0 x 7.5 0.068 -368 7.5 x 9.0 x 7.5 0.1 -410 9.0 x 11.0 x 7.5 Note Further C-values upon request RECOMMENDED PACKAGING TYPE OF HEIGHT (H) REEL DIAMETER / ORDERING CODE PCM LETTER CODE PACKAGING (mm) BOX SIZE (mm) EXAMPLES 5 D Ammo 16.5 55 x 210 x 340 MKP1837-322-162-D X G Ammo 18.5 55 x 210 x 340 MKP1837-322-162-G X F Reel 16.5 350 MKP1837-322-162-F X W Reel 18.5 350 MKP1837-322-162-W X - Bulk - - MKP1837-322-162 X SPACE REQUIREMENTS FOR PRINTED-CIRCUIT BOARD APPLICATIONS AND DIMENSION TOLERANCES For the maximum product dimensions and maximum space requirements for length (l ), width (w ) and height (h ) max. max. max. following tolerances must be taken in account in the envelopment of the components as shown in the drawings below: For products with pitch 15 mm, w = l = 0.3 mm and h = 0.1 mm For products with 15 mm < pitch 27.5 mm, w = l = 0.5 mm and h = 0.1 mm For products with pitch = 37.5 mm, w = l = 0.7 mm and h = 0.5 mm For products with pitch = 52.5 mm, w = l = 1.0 mm and h = 0.5 mm Revision: 27-Sep-2021 Document Number: 26017 2 For technical questions, contact: dc-film vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000
