P
www.vishay.com
Vishay Sfernice
High Precision Wraparound - Wide Ohmic Value Range
Thin Film Chip Resistors, Sulfur Resistant
FEATURES
Load life stability 0.02 % typical at 8000 h
at 70 C under Pd (0.033 % maximum)
Available
Low temperature coefficient down to 5 ppm/C
(-55 C; +155 C)
Available
Very low noise < - 35 dB and voltage coefficient
< 0.01 ppm/V
Wide resistance range: 10 to 200 M
Available
depending on size
Tolerances to 0.01 %
In lot tracking 5 ppm/C Available
Termination: Thin film technology
Short circuits (jumpers) r < 50 mR, I < 2 A, see PZR
datasheet (www.vishay.com/doc?53053)
For low noise and precision applications, superior stability,
Withstand moisture resistance test of AEC-Q200
low temperature coefficient of resistance, and low voltage
Sulfur resistant (per ASTM B809-95 humid vapor test)
coefficient, Vishay Sfernices proven precision thin film
Material categorization: for definitions of compliance
wraparound resistors exceed requirements of
please see www.vishay.com/doc?99912
MIL-PRF-55342G characteristics Y 10 ppm/C (-55 C;
Note
+155 C) down to 5 ppm/C (-55 C; +155 C).
* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details
STANDARD ELECTRICAL SPECIFICATIONS
RATED RATED LIMITING
RESISTANCE TEMPERATURE
POWER POWER ELEMENT TOLERANCE
(2)
MODEL SIZE RANGE COEFFICIENT
W W VOLTAGE %
() ppm/C
(1) (1)
Pn Pd V
P0302 0302 10 to 750K 0.040 0.030 25 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
P0402 0402 10 to 1.5M 0.063 0.040 50 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
P0505 0505 10 to 4M 0.125 0.050 50 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
P0603 0603 10 to 3.2M 0.125 0.100 75 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
(3)
P0805 0805 10 to 10M 0.200 0.125 150 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
P1005 1005 10 to 8.1M 0.250 0.125 75 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
P1206 1206 10 to 35M 0.330 0.250 200 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
P1505 1505 10 to 15M 0.350 0.175 200 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
(4)
P2010 2010 10 to 76M 1 0.500 300 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
(4)
P2512 2512 10 to 200M 2 1 300 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1, 2, 5 5, 10, 25, 50, 100
Notes
(1)
Pn = nominal power - Pd = derated power intended to improve stability
(2)
For ohmic range versus tolerance and TCR see detailed table on next page
(3)
Model P0805 being same size than case 0705 with same performances, only codification of P0805 remains
(4)
With special assembly care
CLIMATIC SPECIFICATIONS MECHANICAL SPECIFICATIONS
Operating temperature Substrate Alumina
-55 C; +155 C
range
Technology Thin film
Note
Nickel chromium with mineral
For temperature up to 230 C, see PHT datasheet Film
passivation or CrSi
(www.vishay.com/doc?53050)
Protection Epoxy + silicone
B type: SnPb over nickel barrier for
PERFORMANCE VS. HUMID SULFUR VAPOR
solder reflow
50 C 2 C, 85 % 4 % RH,
Test conditions Terminations N type: SnAg over nickel barrier
exposure time 500 h
G type: gold over nickel barrierfor
Resistance drift < (0.05 % R + 0.05 ), other applications
Test results
no corrosion products observed
Revision: 05-May-17 Document Number: 53017
1
For technical questions, contact: sferthinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
P
www.vishay.com
Vishay Sfernice
DIMENSIONS in millimeters (inches)
A
D D
B
C
E E
AB
MAX. TOL. MAX. TOL.
D/E
+0.152 (+0.006) +0.127 (+0.005)
CASE SIZE C
MIN. TOL. MIN. TOL.
-0.152 (-0.006) -0.127 (-0.005)
NOMINAL NOMINAL NOMINAL TOLERANCE
0302 0.75 (0.029) 0.60 (0.024) 0.15 (0.006) 0.08 (0.003)
0402 1.00 (0.039) 0.60 (0.024) 0.25 (0.010) 0.1 (0.004)
0505 1.27 (0.005) 1.27 (0.050)
0603 1.52 (0.060) 0.85 (0.033)
0.38 (0.015)
0805 1.91 (0.075) 1.27 (0.050)
0.5 (0.02)
0.127 (0.005)
1005 2.54 (0.100) 1.27 (0.050)
0.13 (0.005)
1206 3.06 (0.120) 1.60 (0.063) 0.40 (0.016)
1505 3.81 (0.150) 1.32 (0.052)
0.48 (0.019)
2010 5.08 (0.200) 2.54 (0.100)
2512 6.30 (0.248) 3.30 (0.130) 0.48 (0.019)
Note
Case 0805 being same than case 0705, only codification of 0805 remains
SUGGESTED LAND PATTERN (to IPC-7351A)
G
min.
X
max.
Z
max.
DIMENSIONS in millimeters (inches)
CHIP SIZE
Z G X
max. min. max.
0302 1.30 (0.051) 0.15 (0.006) 0.73 (0.029)
0402 1.55 (0.061) 0.15 (0.006) 0.73 (0.029)
0505 1.82 (0.072) 0.10 (0.004) 1.40 (0.055)
0603 2.37 (0.093) 0.35 (0.014) 0.98 (0.039)
0805 2.76 (0.109) 0.74 (0.029) 1.40 (0.055)
1005 3.39 (0.133) 1.37 (0.054) 1.40 (0.055)
1206 3.91 (0.154) 1.85 (0.073) 1.73 (0.068)
1505 4.66 (0.183) 2.44 (0.096) 1.45 (0.057)
2010 5.93 (0.233) 3.71 (0.146) 2.67 (0.105)
2512 7.15 (0.281) 4.93 (0.194) 3.43 (0.135)
Revision: 05-May-17 Document Number: 53017
2
For technical questions, contact: sferthinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000