PT020BJ101 Vishay

Not for New Designs Models PT-10 and PT-20 www.vishay.com Vishay Dale Through-Hole Transformers Pulse, Trigger Type FEATURES Choice of printed circuit or bobbin-type configurations Designed to transfer high amplitude or long duration pulses without saturation Designed for low-cost trigger source isolation in half and full wave SCR power control circuits, including motor speed controls, heater controls and incandescent lighting controls Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 STANDARD ELECTRICAL SPECIFICATIONS PRIMARY LEAKAGE INTERWINDING DASH TURNS DCR MAX. UNIPOLAR FIGURE IND. MIN. IND. MAX. CAPACITY MAX. NUMBER RATIO () ET (V-s) (H) (H) (pF) (1) 101 1:1 10 % 1/3 200 3 800 1.5-1.5 570 (1) 102 1:1 10 % 1/3 500 6 1500 4.5-4.5 912 (1) 103 1:1 10 % 1/3 1000 12 2000 8-8 1283 104 1:1 10 % 1/3 2000 13 2800 12-12 1853 105 1:1 10 % 1/3 5000 15 3500 18-18 2850 (1) 106 1:1:1 10 % 2/4 200 3 800 2-2-2 570 107 1:1:1 10 % 2/4 500 6 1500 6-6-6 912 108 1:1:1 10 % 2/4 1000 12 2000 10-10-10 1283 (1) 109 1:1:1 10 % 2/4 2000 13 2800 15-15-15 1853 110 1:1:1 10 % 2/4 5000 15 3500 27-27-27 2850 (1) 111 2:1 10 % 1/3 500 6 1000 4-2 912 (1) 112 2:1 10 % 1/3 1000 10 1300 10-2 1288 113 2:1 10 % 1/3 2000 12 1800 10-5 1881 114 2:1 10 % 1/3 5000 15 2400 18-10 2850 (1) 115 2:1:1 10 % 2/4 200 8 700 4-2-2 570 (1) 116 2:1:1 10 % 2/4 500 11 1000 6-2-2 912 (1) 117 2:1:1 10 % 2/4 1000 15 1300 5-2-2 1311 118 2:1:1 10 % 2/4 2000 60 2000 10-5-5 1881 119 2:1:1 10 % 2/4 5000 75 2100 20-10-10 2850 (1) 120 5:1 10 % 1/3 5000 1500 400 19-3 2850 121 5:1:1 10 % 2/4 5000 1500 400 20-4-4 2850 Note (1) Standard items in PT-10 Model. Other dash numbers available on request. All dash numbers standard in PT-20 model ELECTRICAL SPECIFICATIONS MATERIAL SPECIFICATIONS Primary inductance values: from 200 H to 5000 H Bobbin: nylon Turns ratio: 1:1, 1:1:1, 2:1, 2:1:1 and 5:1 Leads: tinned, solderable Temperature range: -10 C to +70 C PT-10 = polyurethane insulated magnet wire for clip or bracket mounting Dielectric test at 60 Hz: 1600 V (windings to case) RMS PT-20 = tinned copper 0.025 0.635 sq. for printed circuit AC line voltage at 60 Hz: 240 V maximum in test circuits RMS mounting shown Header: thermoset plastic Covering: thermoplastic Revision: 08-Aug-16 Document Number: 34073 1 For technical questions, contact: magnetics vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000Not for New Designs Models PT-10 and PT-20 www.vishay.com Vishay Dale CIRCUIT DIAGRAMS Load Load Line Line Transformer Coupled Unijunction Transistor Triggering Circuit Transformer Coupled Breakdown Diode Triggering Circuit DIMENSIONS in inches (millimeters) PT-10 PT-10 0.010 0.254 0.010 0.254 0.593 0.062 0.593 0.062 Dia., 6 Leads 15.06 1.57 Dia., 4 Leads 15.06 1.57 0.828 0.062 0.828 0.062 Dia. Dia. 21.03 1.57 21.03 1.57 NAT. 5 6 NAT. RED 1 2 RED GRN. 34 GRN. RED 1 2 RED GRN. 3 4 GRN. 1.50 38.10 Min. Typ. 1.50 38.10 Min. Typ. RED GRN. RED GRN. NAT. 1 3 1 3 5 PRI. SEC. PRI. SEC. TER. 2 4 2 4 6 RED RED GRN. NAT. GRN. Figure 1 Figure 2 PT-20 PT-20 0.800 20.32 0.800 20.32 0.968 24.59 0.968 24.59 Max. Max. 0.775 19.68 0.775 19.68 Max. Max. 0.250 0.250 Max. Max. 6.35 6.35 Min. Min. 24 2 4 0.600 15.24 5 6 0.600 15.24 0.300 7.62 0.300 7.62 13 Ref. 1 3 Ref. 0.250 6.35 0.250 6.35 0.025 0.635 Sq. Ref. Ref. 0.025 0.635 Sq 0.500 4 Leads 0.500 6 Leads 12.70 12.70 1 3 1 35 PRI. SEC. PRI. SEC. TER. 24 24 6 Figure 3 Figure 4 PART MARKING - Vishay Dale - Model - Style - Dash number Revision: 08-Aug-16 Document Number: 34073 2 For technical questions, contact: magnetics vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000