PTCCL21H102FBE Vishay

PTCCL - 145 V Series www.vishay.com Vishay BCcomponents 145 V PTC Thermistors for Overload Protection FEATURES Wide range of trip and non-trip currents: From 47 mA up to 1 A for the non-trip current Small ratio between trip and non-trip currents (I /I = 1.5 at 25 C) t nt High maximum inrush current (up to 13 A) Leaded parts withstand mechanical stresses and vibration UL file E148885 according to XGPU standard UL1434 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS Overload (current, voltage, temperature) protection in: Telecommunications Industrial electronics Consumer electronics Electronic data processing DESCRIPTION QUICK REFERENCE DATA These directly heated ceramic-based thermistors have a PARAMETER VALUE UNIT positive temperature coefficient and are primarily intended Maximum voltage (RMS or DC) 145 V for overload protection. They consist of a ceramic pellet Maximum holding current (I ) 0.047 to 1 A nt soldered between two tinned CCS wires and coated with a Resistance at 25 C (R ) 1.3 to 240 25 UL 94 V-0 high temperature hard silicone lacquer. Tolerance on R value 20 % 25 Maximum overload current I 0.2 to 13 A ol MOUNTING Switching temperature 135 to 140 C PTC thermistors can be mounted by wave, reflow, or Operating temperature range hand-soldering. Current levels have been determined 0 to 70 C at max. voltage according IEC 60738 conditions. Different ways of Storage temperature -40 to +175 C mounting or connecting the thermistors can influence their thermal and electrical behavior. Standard operation is in still QUALITY air, any potting or encapsulation of PTC thermistors is not recommended and will change its operating characteristics. UL approved PTCs are guaranteed to withstand severe test programs and have factory audited follow-up programs. Typical Soldering Major UL qualification tests are long-life (6000 cycles) 235 C duration: 5 s (Lead (Pb)-bearing) electrical cycle tests at trip-current, long-life stability 245 C, duration: 5 s (Lead (Pb)-free) storage tests (3000 h at 250 C), damp heat and water Resistance to Soldering Heat immersion tests and over-voltage tests up to 200 % of rated 260 C, duration: 10 s max. voltage. UL approved PTCs are guaranteed to withstand severe test MARKING programs Only the grey lacquered thermistors with a diameter of Long-life cycle tests (over 5000 trip cycles) 8.5 mm to 20.5 mm are marked with BC, R value (example 25 1R9) on one side and I , V on the other side. Long-life storage tests (3000 h at 250 C) nt max. Electrical cycle tests at low ambient temperatures (-40 C or 0 C) Damp-heat and water immersion tests Overvoltage tests at up to 200 % of rated voltage Revision: 21-Sep-15 Document Number: 29086 1 For technical questions, contact: nlr vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 PTCCL - 145 V Series www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING INFORMATION ORDERING PART NUMBERS I MAX. I MIN. R I MAX. I MAX. at DISSIP. D nt t 25 ol res at 25 C at 25 C 20 % at 25 C V and FACTOR MAX. max. BULK TAPE ON REEL (1) (1) (2) (1) (1) (mA) (mA) () (mA) 25 C (mA) (mW/K) (mm) 47 70 240 200 9 7.3 5 PTCCL05H470FBE PTCCL05H470FTE 65 100 115 300 11 7.3 5 PTCCL05H650FBE PTCCL05H650FTE 93 140 55 450 13 7.3 5 PTCCL05H930FBE PTCCL05H930FTE 110 165 40 500 13 7.3 5 PTCCL05H111FBE PTCCL05H111FTE 130 195 28 600 13 7.3 5 PTCCL05H131FBE PTCCL05H131FTE 170 255 19 1000 15 8.3 7 PTCCL07H171FBE PTCCL07H171FTE 210 315 12 1400 15 8.3 7 PTCCL07H211FBE PTCCL07H211FTE 250 375 9.4 2000 16.5 9 8.5 PTCCL09H251FBE PTCCL09H251FTE 270 405 8 2200 16.5 9 8.5 PTCCL09H271FBE PTCCL09H271FTE 320 480 6.7 3000 19 10.5 10.5 PTCCL11H321FBE PTCCL11H321FTE 360 540 5.3 3500 19 10.5 10.5 PTCCL11H361FBE PTCCL11H361FTE 410 615 4.6 4500 22.5 11.7 12.5 PTCCL13H411FBE PTCCL13H411FTE 450 675 3.8 5000 22.5 11.7 12.5 PTCCL13H451FBE PTCCL13H451FTE 600 900 2.9 7200 28.5 15.5 16.5 PTCCL17H601FBE - 710 1065 2.1 8500 28.5 15.5 16.5 PTCCL17H711FBE - 880 1320 1.7 11 000 37.5 19.8 20.5 PTCCL21H881FBE - 1000 1500 1.3 13 000 37.5 19.8 20.5 PTCCL21H102FBE - Notes (1) The indicated current levels are guaranteed according IEC 60738 mounting conditions. For different mounting conditions the indicated current levels can change and should be evaluated in the application. (2) I is the maximum overload current that may flow through the PTC when it passes from the low ohmic to the high ohmic state. ol max. UL approval: I x 0.85 ol max. CURRENT DEVIATION AS A FUNCTION OF THE AMBIENT TEMPERATURE 250 % 200 I t 150 I nt I 100 ol max. 50 0 -50 -25 025 50 75 100 T (C) amb Revision: 21-Sep-15 Document Number: 29086 2 For technical questions, contact: nlr vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000