CMF (Military RN and RL) www.vishay.com Vishay Dale Metal Film Resistors, Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RL FEATURES Very low noise (- 40 dB) Very low voltage coefficient (5 ppm/V) Controlled temperature coefficient Flame retardant epoxy coating Commercial alternatives to military styles are available with higher power ratings. See CMF Industrial data sheet: (www.vishay.com/doc 31018) STANDARD ELECTRICAL SPECIFICATIONS RESISTANCE RESISTANCE RESISTANCE POWER POWER MAX. RANGE RANGE RANGE RESISTANCE MIL DIELECTRIC (3) GLOBAL MIL RATING RATING WORKING RANGE TOL. SPEC. STRENGTH (1) MODEL STYLE P P VOLTAGE MIL-R-10509 MIL-R-10509 MIL-R-10509 % 70 C 125 C SHEET V AC W W V 100 ppm/C 50 ppm/C 25 ppm/C MIL-PRF-22684 (D) (C) (E) 0.1, 0.25, CMF50 RN50 08 - 0.05 200 - 10 to 100K 10 to 100K - 450 0.5, 1 0.1, 0.25, CMF55 RN55 07 0.125 0.10 200 10 to 301K 49.9 to 100K 49.9 to 100K - 450 0.5, 1 0.1, 0.25, CMF60 RN60 01 0.25 0.125 300 10 to 1M 49.9 to 499K 49.9 to 499K - 500 0.5, 1 0.1, 0.25, CMF65 RN65 02 0.50 0.25 350 10 to 2M 49.9 to 1M 49.9 to 1M - 900 0.5, 1 0.1, 0.25, (2) CMF70 RN70 03 0.75 0.50 500 10 to 2.49M 24.9 to 1M 24.9 to 1M - 900 0.5, 1 CMF07 RL07 01 0.25 - 250 - - - 51 to 150K 2, 5 450 CMF20 RL20 02 0.50 - 350 - - - 4.3 to 470K 2, 5 700 Notes (1) Continuous working voltage shall be P x R or maximum working voltage, whichever is less. (2) Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 rev. D. (3) Tolerances of 0.1 %, 0.25 % and 0.5 % are not applicable to characteristic D. TECHNICAL SPECIFICATIONS PARAMETER UNIT CONDITION Voltage Coefficient ppm/V 5 when measured between 10 % and full rated voltage 10 8 Insulation Resistance 10 min. dry 10 min. after moisture test Operating Temperature Range C - 65/+ 175 (see derating curves for military range) Terminal Strength Ib 5 pound pull test for RL07/RL20 2 pound pull test for all others Continuous satisfactory coverage when tested in accordance Solderability with MIL-R-10509 and MIL-PRF-22684 Revision: 02-May-13 Document Number: 31027 1 For technical questions, contact: ff2aresistors vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 CMF (Military RN and RL) www.vishay.com Vishay Dale GLOBAL PART NUMBER INFORMATION New Global Part Numbering: RN60D3483FR36 (preferred part numbering format) R N 6 0 D 348 3F R 3 6 RESISTANCE TOLERANCE MIL STYLE CHARACTERISTIC PACKAGING SPECIAL VALUE CODE RN50 E = 25 ppm 3 digit significant B = 0.1 % Blank = Standard B14 = Tin/lead, bulk RN55 C = 50 ppm figure, followed by C = 0.25 % (Dash number) BSL = Tin/lead, bulk, D D = 0.5 % RN60 = 100 ppm a multiplier single lot date code 88 = Hot solder dip RN65 F = 1 % Use R for R36 = Tin/lead, T/R (full) 143 = Non-magnetic RN70 values < 100 RE6 = Tin/lead, T/R (1000 pieces) 10R0 = 10 RSL = Tin/lead, T/R, 2152 = 21.5 k single lot date code 2494 = 2.49 M Historical Part Number example: RN60D3483F (will continue to be accepted) RN60 D 3483 F R36 MIL STYLE CHARACTERISTIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: RL07S471JR36 (preferred part numbering format) RL0 7 S 4 7 1 J R 3 6 RESISTANCE TOLERANCE MIL STYLE LEAD MATERIAL PACKAGING SPECIAL VALUE CODE RL07 S = Solderable 2 digit significant G = 2 % B14 = Tin/lead, bulk Blank = Standard figure, followed by RL20 J = 5 % BSL = Tin/lead, bulk, single lot date code (Dash number) a multiplier R36 = Tin/lead, T/R (full) 88 = Hot solder dip Use R for RE6 = Tin/lead, T/R (1000 pieces) 143 = Non-magnetic values < 10 RSL = Tin/lead, T/R, single lot date code 4R3 = 4.3 202 = 2.0 k 474 = 470 k Historical Part Number example: RL07S471J (will continue to be accepted) RL07 S 471 J R36 MIL STYLE LEAD MATERIAL RESISTANCE VALUE TOLERANCE CODE PACKAGING Note For additional information on packaging, refer to the Through Hole Resistor Packaging document (www.vishay.com/doc 31544). MATERIAL SPECIFICATIONS Element Nickel-chrome alloy CAGE CODE: 91637 Flame retardant epoxy, formulated for Coating superior moisture protection Core Fire-cleaned high purity ceramic ENVIRONMENTAL SPECIFICATIONS Standard lead material is solder-coated Termination copper. Solderable and weldable. Environmental performance is shown in the Environmental Performance table. Test methods General are those specified in MIL-R-10509 and APPLICABLE MIL-SPECS MIL-PRF-22684. MIL-R-10509 and MIL-PRF-22684: The CMF models meet Resistance shifts due to storage at room or exceed the electrical, environmental and dimensional Shelf Life temperature are negligible. requirements of MIL-R-10509 and MIL-PRF-22684. Noise: Vishay Dale metal film resistors have exceptionally low noise level. Average for standard resistance range is 0.10 V per V over a decade of frequency, with low and intermediate resistance values typically below 0.05 V per V. Revision: 02-May-13 Document Number: 31027 2 For technical questions, contact: ff2aresistors vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000