SiP32413, SiP32414, SiP32416 www.vishay.com Vishay Siliconix Dual 2 A, 1.2 V, Slew Rate Controlled Load Switch DESCRIPTION FEATURES SiP32413, SiP32414, and SiP32416 are slew rate controlled 1.1 V to 5.5 V operation voltage range load switches that is designed for 1.1 V to 5.5 V operation. 62 m typical from 2 V to 5 V The devices guarantee low switch on-resistance at 1.2 V Low R down to 1.2 V ON input. SiP32413 and SiP32414 feature a controlled soft-on Slew rate controlled turn-on: slew rate of typical 150 s that limits the inrush current for 150 s at 3.6 V for SiP32413, SiP32414 Available designs of capacitive load or noise sensitive loads. 2.5 ms at 3.6 V for SiP32416 SiP32416 features a longer slew rate of typical 2.5 ms to Fast shutdown load discharge for SiP32414 and SiP32416 keep the peak of the inrush current even lower. Low quiescent current The devices feature a low voltage control logic interface < 1 A when disabled (on/off interface) that can interface with low voltage digital 6.7 A at V = 1.2 V IN control without extra level shifting circuit. The SiP32414 and SiP32416 also integrate output discharge switches that Switch off reversed blocking enable fast shutdown load discharge. When the switches Material categorization: for definitions of compliance are off, they provide the reverse blocking to prevent high please see www.vishay.com/doc 99912 current flowing into the power source. All SiP32413, SiP32414, and SiP32416 are available in APPLICATIONS TDFN8 2.0 mm x 2.0 mm package. Each switch in each Cellular phones device can support over 2 A of continuous current. Portable media players Digital camera GPS Computers Portable instruments and healthcare devices TYPICAL APPLICATION CIRCUIT V IN IN OUT V OUT SiP32413, SiP32414, SiP32416 (for one switch) C C IN OUT 4.7 F 0.1 F CNTRL CNTRL GND GND GND Fig. 1 - SiP32413, SiP32414, SiP32416 Typical Application Circuit ORDERING INFORMATION TEMPERATURE RANGE PACKAGE MARKING PART NUMBER AA SiP32413DNP-T1-GE4 -40 C to 85 C TDFN8 2.0 mm x 2.0 mm AB SiP32414DNP-T1-GE4 AG SiP32416DNP-T1-GE4 Note -GE4 denotes halogen-free and RoHS-compliant S20-0532-Rev. C, 06-Jul-2020 Document Number: 71437 1 For technical questions, contact: powerictechsupport vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000SiP32413, SiP32414, SiP32416 www.vishay.com Vishay Siliconix ABSOLUTE MAXIMUM RATINGS PARAMETER LIMIT UNIT Supply input voltage (V ) -0.3 to 6 IN Enable input voltage (V ) -0.3 to 6 V EN Output voltage (V ) -0.3 to 6 OUT Maximum continuous switch current (I)2.4 max. A Maximum pulsed current (pulsed at 1 ms, 10 % duty cycle) 3 ESD rating (HBM) 4000 V Storage temperature (T ) -65 to +150 C stg a Thermal tesistance ( ) 95 C/W JA a Power dissipation (P ) 580 mW D Notes a. Device mounted with all leads and power pad soldered or welded to PC board, see PCB layout b. Derate 10.5 mW/C above T = 70 C, see PCB layout A Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating/conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE PARAMETER LIMIT UNIT Input voltage range (V ) 1.1 to 5.5 V IN Operating junction temperature range (T ) -40 to +125 C J SPECIFICATIONS LIMITS TEST CONDITIONS UNLESS SPECIFIED -40 C to 85 C V = 5 V, T = -40 C to 85 C IN A a b a PARAMETER SYMBOL (typical values are at T = 25 C) UNIT A MIN. TYP. MAX. c Operating voltage V 1.1 - 5.5 V IN V = 1.2 V, CNTRL = active - 6.7 14 IN V = 1.8 V, CNTRL = active - 14 24 IN V = 2.5 V, CNTRL = active - 25 40 IN Quiescent current I Q V = 3.6 V, CNTRL = active - 40 60 IN V = 4.3 V, CNTRL = active - 52 75 A IN V = 5 V, CNTRL = active - 71 99 IN Off supply current I CNTRL = inactive, OUT = open - - 1 Q(off) Off switch current I CNTRL = inactive, OUT = 0 - - 1 DS(off) Reverse blocking current I V = 5 V, V = 1.2 V, V = inactive - - 10 RB OUT IN EN V = 1.2 V, I = 100 mA, T = 25 C - 66 76 IN L A V = 1.8 V, I = 100 mA, T = 25 C - 62 72 IN L A V = 2.5 V, I = 100 mA, T = 25 C - 62 72 IN L A On-resistance R m DS(on) V = 3.6 V, I = 100 mA, T = 25 C - 62 72 IN L A V = 4.3 V, I = 100 mA, T = 25 C - 62 72 IN L A V = 5 V, I = 100 mA, T = 25 C - 62 72 IN L A On-resistance temp. coefficient TC - 3900 - ppm/C RDS V = 1.2 V - - 0.3 IN d V = 1.8 V - - 0.4 IN d V = 2.5 V - - 0.5 IN c CNTRL input low voltage V V IL d V = 3.6 V - - 0.6 IN d V = 4.3 V - - 0.7 IN d V = 5 V - - 0.8 IN S20-0532-Rev. C, 06-Jul-2020 Document Number: 71437 2 For technical questions, contact: powerictechsupport vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000