ST www.vishay.com Vishay SuperTan Wet Tantalum Capacitors with Hermetic Seal FEATURES Very high capacitance 10 F to 1800 F Available 25 V to 125 V DC DC Very low ESR Available High ripple current All tantalum case Hermetically sealed Low DCL Axial through-hole terminations: standard tin / lead (Sn / Pb), 100 % tin (RoHS-compliant) available Material categorization: for definitions of compliance Vishay ST represents a major breakthrough in wet tantalum please see www.vishay.com/doc 99912 capacitor technology. Its unique cathode system provides Note the highest capacitance per unit volume. The design * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non-RoHS-compliant. For facilitates a doubling of capacitance, lower ESR and higher example, parts with lead (Pb) terminations are not RoHS-compliant. ripple current rating compared with conventional wet Please see the information / tables in this datasheet for details. tantalum products. Moreover, the ST has the capacitance stability of a solid tantalum capacitor and there are no circuit APPLICATION NOTES impedance restrictions. a. No continuous reverse voltage permissible. The ST is housed in an all tantalum, hermetically sealed case b. The peak of the applied AC ripple and the applied DC and is manufactured to withstand hazardous environments. voltage must not exceed the DC voltage rating of the The ST is used widely in the defense and aerospace capacitor. industries and whenever there is a space problem. c. Ripple current ratings by part number at 85 C and 40 kHz are included in the table. Ripple current correction PERFORMANCE CHARACTERISTICS factors for other temperatures and frequencies are given Operating Temperature: -55 C to +85 C on the next page. (to +125 C with voltage derating) d. Transient reverse voltage surges are acceptable under Capacitance Tolerance: at 120 Hz, +25 C. the following conditions: 20 % standard. 10 % available as special. the peak reverse voltage does not exceed 1.5 V and the peak current times the duration of the reverse transient does not exceed 0.05 As. In addition, the repetition frequency of the reverse voltage surge is less than 10 Hz. DIMENSIONS in inches millimeters Terminal welded 0.0253 0.002 0.64 0.05 dia. to case (no. 22 AWG) tinned nickel leads 0.250 6.35 solderable and weldable MAX. 0.094 2.38 MAX. Terminal location D DIA. L E E within 0.031 of center 1 MAX. INSULATED L + 0.031 / - 0.016 + 0.79 / - 0.41 1 CASE CODE D 0.016 0.41 E 0.250 6.3 MAX. (DIA.) UNINSULATED T1 0.188 4.78 0.219 5.56 0.453 11.51 1.500 38.10 T2 0.281 7.14 0.312 7.92 0.641 16.28 2.250 57.15 L2 0.281 7.14 0.312 7.92 1.008 25.60 2.250 57.15 T3 0.375 9.52 0.406 10.31 0.766 19.46 2.250 57.15 T4 0.375 9.52 0.406 10.31 1.062 26.97 2.250 57.15 Notes Material at egress is Tantalum Approx. weight: T1: 2.3 g, T2: 5.7 g, Insulation sleeving will lap over the ends of the capacitor case T3: 9.4 g, T4: 14.8 g Revision: 06-Jul-15 Document Number: 43000 1 For technical questions, contact: tantalum vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 ST www.vishay.com Vishay ORDERING INFORMATION ST 220 100 T4 M I E3 Super Tan CAPACITANCE 85 C RATED CASE CODE CAPACITANCE INSULATING RoHS-compliant COMMERCIAL F DC VOLTAGE TOLERANCE SLEEVE CAP. TYPE M = 20 % I = insulated E3 = 100 % tin termination K = 10 % X = uninsulated (RoHS compliant) Blank = SnPb termination (standard design) STANDARD RATINGS MAX. CAPACITANCE AC RIPPLE MAX. DCL AT CAPACITANCE MAX. MAX. IMP. CHANGE AT 85 C AT 25 C CASE ESR AT -55 C 40 kHz PART NUMBER +85 C / AND 120 Hz CODE 120 Hz AND 120 Hz +25 C -55 C +85 C +125 C (mA) +125 C (F) () () (A) (%) (%) (%) RMS (A) 25 V AT 85 C 15 V AT 125 C DC DC 120 T1 1.3 1 5 25 -42 +8 +12 1250 ST120-25T1MI 560 T2 0.83 2 10 12 -65 +10 +15 2100 ST560-25T2MI 1100 L2 0.5 3 25 7 -60 +20 +45 3200 ST1100-25L2MI 1200 T3 0.65 5 20 7 -70 +12 +18 2600 ST1200-25T3MI 1800 T4 0.5 6 25 7 -72 +12 +20 3100 ST1800-25T4MI 30 V AT 85 C 20 V AT 125 C DC DC 100 T1 1.3 1 5 25 -38 +8 +12 1200 ST100-30TMI 470 T2 0.85 2 10 15 -65 +10 +18 1800 ST470-30T2MI 950 L2 0.5 5 30 7 -55 +18 +35 3200 ST950-30L2MI 1000 T3 0.7 7 25 7 -70 +10 +18 2500 ST1000-30T3MI 1500 T4 0.6 12 35 6 -72 +10 +20 3000 ST1500-30T4MI 50 V AT 85 C 30 V AT 125 C DC DC 68 T1 1.5 1 5 35 -25 +8 +15 1050 ST68-50T1MI 220 T2 0.9 2 10 17.5 -50 +8 +15 1800 ST220-50T2MI 450 L2 0.6 3 25 7.5 -45 +12 +30 2900 ST450-50L2MI 470 T3 0.75 3 25 10 -45 +8 +15 2100 ST470-50T3MI 680 T4 0.7 5 40 8 -58 +10 +20 2750 ST680-50T4MI 60 V AT 85 C 40 V AT 125 C DC DC 47 T1 2.0 1 5 44 -25 +8 +12 1050 ST47-60T1MI 150 T2 1.1 2 10 20 -40 +8 +15 1800 ST150-60T2MI 370 L2 0.6 3 25 9 -33 +9 +20 2900 ST370-60L2MI 390 T3 0.9 3 25 15 -45 +8 +15 2100 ST390-60T3MI 560 T4 0.8 5 40 10 -58 +8 +15 2750 ST560-60T4MI 75 V AT 85 C 50 V AT 125 C DC DC 33 T1 2.5 1 5 66 -25 +5 +9 1050 ST33-75T1MI 110 T2 1.3 2 10 24 -35 +6 +10 1650 ST110-75T2MI 250 L2 0.8 5 30 12 -30 +6 +15 2500 ST250-75L2MI 330 T3 1.0 3 30 12 -45 +6 +10 2100 ST330-75T3MI 470 T4 0.9 5 50 12 -50 +6 +10 2750 ST470-75T4MI Notes (K = 10 %, M = 20 %) and insulation letter (I = insulation, X = uninsulated) Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following the letter X from 0 to 9. For units with outer plastic-film insulation, substitute 2 for 0 at the end of the part number For RoHS-compliant add E3 for suffix Revision: 06-Jul-15 Document Number: 43000 2 For technical questions, contact: tantalum vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000