TNPV12061M20BEEN Vishay

TNPV e3 www.vishay.com Vishay Draloric High Voltage Thin Film Flat Chip Resistors FEATURES High operating voltage U up to 1000 V max. Low voltage coefficient < 1 ppm/V Excellent overall stability at different environmental conditions 0.05 % (1000 h rated power at 70 C) Superior moisture resistivity (85 C 85 % RH) AEC-Q200 qualified Sulfur resistance verified according to ASTM B 809 Material categorization: for definitions of compliance TNPV e3 precision thin film flat chip resistors are the perfect please see www.vishay.com/doc 99912 choice for most fields of modern electronics where the highest reliability and stability at high operating voltages are APPLICATIONS of major concern. Typical applications include industrial and automotive inverters, voltage measurement systems as Industrial and automotive inverters implemented in battery management systems, and test and Battery management system measuring equipment. Test and measuring equipment TECHNICAL SPECIFICATIONS DESCRIPTION TNPV1206 e3 TNPV1210 e3 (1) Imperial size 1206 1210 (1) Metric size code RR3216M RR3225M Resistance range 160 k to 2 M 121 k to 3.01 M Resistance tolerance 1 % 0.5 % 0.1 % Temperature coefficient 50 ppm/K 25 ppm/K 15 ppm/K 10 ppm/K Voltage coefficient c < 1 ppm/V (2) Rated dissipation, P 0.25 W 0.33 W 70 Maximum operating voltage, U AC max. RMS 700 V 1000 V (3) or DC (2) Permissible film temperature, 155 C F max. Operating temperature range -55 C to 125 C (155 C) Notes (1) Size not specified in EN 140401-801 (2) Please refer to APPLICATION INFORMATION below (3) Application-specific safety requirements may set limitations to the applicability of the specified voltage APPLICATION INFORMATION The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials may be required to maintain the reliability of the assembly. These resistors do not feature a lifetime limitation when operated within the limits of rated dissipation, permissible operating voltage, and permissible film temperature. However, the resistance typically increases due to the resistor s film temperature over operating time, generally known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional lifetime. The designer may estimate the performance of the particular resistor application or set certain load and temperature limits in order to maintain a desired stability. Revision: 18-Jun-2020 Document Number: 28881 1 For technical questions, contact: thinfilmchip vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TNPV e3 www.vishay.com Vishay Draloric MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION OPERATION MODE STANDARD TNPV1206 e3 0.25 W Rated dissipation, P 70 TNPV1210 e3 0.33 W Applied maximum film temperature, max. 125 C F TNPV1206 e3 160 k to 2 M TNPV1210 e3 121 k to 3.01 M Max. resistance change at P for resistance 70 1000 h 0.05 % range R/R, after: 8000 h 0.10 % 225 000 h 0.30 % TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE TCR TOLERANCE RESISTANCE E-SERIES 50 ppm/K 1 % E24 E96 0.5 % 25 ppm/K TNPV1206 e3 0.1 % 160 k to 2.0 M E24 E192 15 ppm/K 0.1 % 10 ppm/K 0.1 % 50 ppm/K 1 % E24 E96 121 k to 3.01 M 0.5 % 25 ppm/K TNPV1210 e3 0.1 % E24 E192 15 ppm/K 0.1 % 121 k to 2.13 M 10 ppm/K 0.1 % PACKAGING TYPE / SIZE CODE QUANTITY PACKAGING STYLE WIDTH PITCH PACKAGING DIMENSIONS (1) E52 = EN 1000 180 mm / 7 TNPV1206 e3 Paper tape according ET1 = EA 5000 8 mm 4 mm TNPV1210 e3 IEC 60286-3, Type 1a ET6 = EC 20 000 330 mm / 13 Note (1) 1000 pieces packaging is available only for precision resistors with tolerance 0.1 % PART NUMBER AND PRODUCT DESCRIPTION Part Number: TNPV12061M24DEEA T N P V 1 2 061 M 2 4D E E A TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING SPECIAL TNPV1206 R = decimal B = 0.1 % H = 50 ppm/K EA Up to 2 digits TNPV1210 K = thousand D = 0.5 % E = 25 ppm/K EC Blank = standard M = million F = 1.0 % X = 15 ppm/K EN (4 digits) Y = 10 ppm/K Product Description: TNPV1206 1M24 0.5 % T-9 ET1 e3 TNPV1206 1M24 0.5 % T-9 ET1 e3 TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING LEAD (Pb)-FREE TNPV1206 Examples: 0.1 % T-2 = 50 ppm/K ET1 e3 = pure tin 1M24 = 1.24 M 0.5 % T-9 = 25 ppm/K ET6 TNPV1210 termination finish 560K = 560 k 1.0 % T-10 = 15 ppm/K E52 T-13 = 10 ppm/K Note Products can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION Revision: 18-Jun-2020 Document Number: 28881 2 For technical questions, contact: thinfilmchip vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000