333 3 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved dark sensitivity Improved immunity against optical noise Improved immunity against Wi-Fi noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 23051 MECHANICAL DATA ADDITIONAL RESOURCES Pinning for TSOP13...: 1 = OUT, 2 = GND, 3 = V S 3D Models DESCRIPTION The TSOP13... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The robustness against spurious pulses originating from Wi-Fi signals has been enhanced. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. Th e demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP131.., TSOP133.., and TSOP135.. series devices are designed to receive short burst codes (6 or more carrier cycles per burst). The third digit designates the AGC level (AGC1, AGC3, or AGC5) and the last two digits designate the band-pas s frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC1 provides basic noise suppression, AGC3 provides enhanced noise suppression and AGC5 provides maximized nois e suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. These components have not been qualified to automotive specifications. PARTS TABLE BASIC NOISE SUPPRESSION ENHANCED NOISE MAXIMIZED NOISE AGC (AGC1) SUPPRESSION (AGC3) SUPPRESSION (AGC5) 30 kHz TSOP13130 TSOP13330 TSOP13530 33 kHz TSOP13133 TSOP13333 TSOP13533 (1) 36 kHz TSOP13136 TSOP13336 TSOP13536 Carrier frequency (2)(4) 38 kHz TSOP13138 TSOP13338 TSOP13538 40 kHz TSOP13140 TSOP13340 TSOP13540 (3) 56 kHz TSOP13156 TSOP13356 TSOP13556 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) (2) (3) (4) Best choice for RCMM RECS-80 Code r-map XMP-1, XMP-2 Note 30 kHz and 33 kHz only available on written request Rev. 1.4, 17-Dec-2019 Document Number: 82805 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-11 R 3 1 Transmitter IR receiver with 30 k V + V S S TSALxxxx C 1 1 C OUT Band Demo- Input AGC pass dulator V O GND GND 2 PIN Control circuit and C recommended to reduce supply ripple for V < 2.8 V R 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.55 0.70 0.90 mA v S SD Supply current E = 40 klx, sunlight I -0.80- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 30 - m IR diode TSAL6200, I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 3.0/f < t < t + 3.5/f , E - 0.08 0.15 mW/m pi 0 po pi 0 e min. test signal see Fig. 1 t - 3.0/f < t < t + 3.5/f , pi 0 po pi 0 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 t - 3.0/f < t < t + 3.5/f , test pi o po pi o Maximum long burst irradiance 2 signal see Fig. 1, dark ambient, E 0.5 - - W/m e max. (AGC3, AGC5) burst length > 30 cycles Angle of half transmission Directivity - 45 - deg 1/2 distance Rev. 1.4, 17-Dec-2019 Document Number: 82805 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit