333 3 TSOP181.., TSOP183.., TSOP185.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved dark sensitivity Improved immunity against optical noise Improved immunity against Wi-Fi noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency 1 Supply voltage: 2.5 V to 5.5 V 22 Material categorization: 33 19026 for definitions of compliance please see www.vishay.com/doc 99912 ADDITIONAL RESOURCES MECHANICAL DATA 3D Models 1 = OUT, 2 = GND, 3 = V S DESCRIPTION The TSOP18... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The robustness against spurious pulses originating from Wi-Fi signals has been enhanced. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. Th e demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP181.., TSOP183.., and TSOP185.. series devices are designed to receive short burst codes (6 or more carrier cycles per burst). The third digit designates the AGC level (AGC1, AGC3, or AGC5) and the last two digits designate the band-pas s frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC1 provides basic noise suppression, AGC3 provides enhanced noise suppression and AGC5 provides maximized nois e suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. These components have not been qualified to automotive specifications. PARTS TABLE BASIC NOISE SUPPRESSION ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION AGC (AGC1) (AGC3) (AGC5) 30 kHz TSOP18130 TSOP18330 TSOP18530 33 kHz TSOP18133 TSOP18333 TSOP18533 (1) 36 kHz TSOP18136 TSOP18336 TSOP18536 Carrier (2)(4) frequency 38 kHz TSOP18138 TSOP18338 TSOP18538 40 kHz TSOP18140 TSOP18340 TSOP18540 (3) 56 kHz TSOP18156 TSOP18356 TSOP18556 Package Minicast Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) Best choice for RCMM RECS-80 Code r-map XMP-1, XMP-2 Note 30 kHz and 33 kHz only available on written request Rev. 1.4, 17-Dec-2019 Document Number: 82802 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D TSOP181.., TSOP183.., TSOP185.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-11 R 1 3 Transmitter IR receiver with V + V 30 k S S TSALxxxx C 1 1 C Band Demo- OUT Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.55 0.70 0.90 mA v S SD Supply current E = 40 klx, sunlight I -0.80- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V -- 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 3.0/f < t < t + 3.5/f , test signal see Fig. 1 pi 0 po pi 0 2 Maximum irradiance t - 3.0/f < t < t + 3.5/f , test signal see Fig. 1 E 30 - - W/m pi 0 po pi 0 e max. Maximum long burst t - 3.0/f < t < t + 3.5/f , test signal see Fig. 1, pi o po pi o 2 E 0.5 - - W/m e max. irradiance (AGC3, AGC5) dark ambient, burst length > 30 cycles Directivity Angle of half transmission distance - 45 - deg 1/2 Rev. 1.4, 17-Dec-2019 Document Number: 82802 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit