TSOP321.., TSOP323.., TSOP325.., TSOP341.., TSOP343.., www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise 1 22 Material categorization: 33 16672 for definitions of compliance please see www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS DESCRIPTION Models These products are miniaturized receivers for infrared Available remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package contains an MECHANICAL DATA IR filter. The demodulated output signal can be directly Pinning for TSOP341.., TSOP343.., TSOP345..: connected to a microprocessor for decoding. 1 = OUT, 2 = GND, 3 = V S The TSOP323.., TSOP343..series devices are optimized to Pinning for TSOP321.., TSOP323.., TSOP325..: suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data 1 = OUT, 2 = V , 3 = GND S signals if continuously transmitted. The TSOP321.., TSOP341.. series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP323.., TSOP343.. series containing the newer AGC3. The TSOP325.., TSOP345.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP34130 TSOP32130 TSOP34330 TSOP32330 TSOP34530 TSOP32530 33 kHz TSOP34133 TSOP32133 TSOP34333 TSOP32333 TSOP34533 TSOP32533 (1)(6) (1)(6) 36 kHz TSOP34136 TSOP32136 TSOP34336 TSOP32336 TSOP34536 TSOP32536 Carrier (2)(3)(4)(5) (2)(3)(4)(5) frequency 38 kHz TSOP34138 TSOP32138 TSOP34338 TSOP32338 TSOP34538 TSOP32538 40 kHz TSOP34140 TSOP32140 TSOP34340 TSOP32340 TSOP34540 TSOP32540 56 kHz TSOP34156 TSOP32156 TSOP34356 TSOP32356 TSOP34556 TSOP32556 Package Mold 1 = OUT, 1 = OUT, 2 = V , 1 = OUT, 1 = OUT, 2 = V , 1 = OUT, 1 = OUT, 2 = V , S S S Pinning 2 = GND, 3 = V 3 = GND 2 = GND, 3 = V 3 = GND 2 = GND, 3 = V 3 = GND S S S Dimensions (mm) 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 RCMM Rev. 1.7, 24-Sep-2018 Document Number: 82490 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP321.., TSOP323.., TSOP325.., TSOP341.., TSOP343.., www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-11 R 1 3 Transmitter IR receiver with 30 k V + V S S TSALxxxx C 1 1 C OUT Band Demo- Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 30 - m I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.08 0.15 mW/m pi o po pi o e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 45 - 1/2 distance Rev. 1.7, 24-Sep-2018 Document Number: 82490 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit