TSOP372..H, TSOP374..H www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detectors and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise External metal shield Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 2225942594 DESCRIPTION The TSOP372..H, TSOP374..H series are miniaturized receiver modules for infrared remote control systems. A PIN click logo to get started DESIGN SUPPORT TOOLS diode and a preamplifier are assembled on a PCB, the epoxy lens cap contains an IR filter. Models The TSOP374..H series devices are optimized to suppress Available almost all spurious pulses from energy saving lamps like CFLs. The AGC4 used in the TSOP374..H may suppress ORDERING CODE some data signals. The TSOP372..H series are provided Taping: primarily for compatibility with old AGC2 designs. New TSOP37...TT1 - top view taped designs should prefer the TSOP374..H series containing the TSOP37...TT2 - top view taped newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) (1)(/2)(3) 36 kHz TSOP37236H TSOP37436H (4)(5)(8) 38 kHz TSOP37238H TSOP37438H Carrier frequency 40 kHz TSOP37240H TSOP37440H H(6)(7) 56 kHz TSOP37256H TSOP37456 Package Belobog shield Pinning 1 = OUT, 2, 3, 6, 7, 8 = GND, 4, 5 = V S Dimensions (mm) 4.3 W x 4.3 H x 1.0 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) (6) (7) (8) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA r-map Rev. 2.1, 24-Sep-2018 Document Number: 82622 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP372..H, TSOP374..H www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 4, 5 17170-11 R V 1 S Transmitter 30 k IR receiver with V + V S S 1 TSALxxxx C 1 OUT Demo- Band C Input AGC dulator pass OUT V 2, 3, O GND GND 6, 7, 8 GND PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 20445-5 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 3.3 V, E = 0 I 0.27 0.35 0.45 mA S v SD Supply current E = 40 klx, sunlight I -0.45- mA v SH E = 0, IR diode TSAL6200, v Transmission distance d- 24 - m I = 50 mA, test signal see Fig. 1 F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f E - 0.12 0.25 mW/m pi o po pi o, e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 75 - 1/2 distance Rev. 2.1, 24-Sep-2018 Document Number: 82622 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit