TSOP392.., TSOP394.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES 4 3 Very low supply current 2 1 Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Two lenses for high sensitivity Insensitive to supply voltage ripple and noise Ultra small top-view PCB footprint Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 DESCRIPTION 22963 The TSOP39... series are miniaturized receiver modules for infrared remote control systems. Two PIN diodes and a click logo to get started DESIGN SUPPORT TOOLS preamplifier are assembled on a leadframe, the epoxy package contains an IR filter. The demodulated output Models signal can be directly connected to digital circuitry for Available decoding. The TSOP394.. series devices are optimized to suppress MECHANICAL DATA almost all spurious pulses from energy saving lamps like Pinning: CFLs. The AGC4 used in the TSOP394.. may suppress 1, 4 = GND, 2 = V , 3 = OUT S some data signals. The TSOP392.. series are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP394.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC AND LONG BURSTS (AGC2) AND LONG BURSTS (AGC4) 30 kHz TSOP39230 TSOP39430 33 kHz TSOP39233 TSOP39433 (1)(2)(3) 36 kHz TSOP39236 TSOP39436 Carrier frequency (4)(5) 38 kHz TSOP39238 TSOP39438 40 kHz TSOP39240 TSOP39440 (6)(7) 56 kHz TSOP39256 TSOP39456 Package TVCast Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 2.6 H x 5.3 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Rev. 1.4, 24-Sep-2018 Document Number: 82778 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP392.., TSOP394.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 2 17170-11 R 1 V S Transmitter IR receiver 30 k with V + V S S 3 TSALxxxx C 1 OUT Band Demo- C Input AGC OUT pass dulator V O 1, 4 GND GND PIN GND Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH E = 0, test signal see Fig. 1, v Transmission distance d- 30 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.08 0.12 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 1.0 Optical Test Signal E e Output pulse width (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) F 0 0.9 0.8 Input burst length 0.7 t 0.6 t * pi 0.5 T 0.4 * t 10/f is recommended for optimal function pi 0 0.3 Output Signal 16110 V = 950 nm, O 0.2 Optical test signal, fig. 1 1) 7/f < t < 15/f V 0 d 0 OH 0.1 2) t - 5/f < t < t + 6/f pi 0 po pi 0 0 V OL 0.1 1 10 100 1000 10 000 1) 2) t t t d po 20743 E - Irradiance (mW/m) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.4, 24-Sep-2018 Document Number: 82778 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit