TSOP4338 Vishay

333 3 TSOP21.., TSOP23.., TSOP41.., TSOP43.., TSOP25.., TSOP45.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light 1 22 Insensitive to supply voltage ripple and noise 33 16672 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Product Page 3D Models Calculators Marking Packages Pinning for TSOP41.., TSOP43.., TSOP45..: 1 = OUT, 2 = GND, 3 = V S Holders Bends and Cuts Pinning for TSOP21.., TSOP23.., TSOP25..: 1 = OUT, 2 = V , 3 = GND S DESCRIPTION These products are miniaturized receivers for infrared ORDERING CODE remote control systems. A PIN diode and a preamplifier are TSOP2..., TSOP4... - 2160 pieces in tubes assembled on a lead frame, the epoxy package contains a n IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. BLOCK DIAGRAM The TSOP23.., TSOP43.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL V S sources. They may suppress some data signals if 30 k continuously transmitted. OUT The TSOP21.., TSOP41.. series devices are provided primarily for compatibility with old AGC1 designs. New Band Demo- Input AGC pass dulator designs should prefer the TSOP23.., TSOP43.. series containing the newer AGC3. The TSOP25.., TSOP45.. series GND are useful to suppress even extreme levels of optical noise , PIN Control circuit but may also suppress some data signals. Please check compatibility with your codes. 16833-22 These components have not been qualified according to automotive specifications. APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 2.0, 14-Dec-2021 Document Number: 82460 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP21.., TSOP23.., TSOP41.., TSOP43.., TSOP25.., TSOP45.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP4130 TSOP2130 TSOP4330 TSOP2330 TSOP4530 TSOP2530 33 kHz TSOP4133 TSOP2133 TSOP4333 TSOP2333 TSOP4533 TSOP2533 (1) (1) (1) 36 kHz TSOP4136 TSOP2136 TSOP4336 TSOP2336 TSOP4536 TSOP2536 Carrier frequency (2)(3)(4)(5) (2)(3)(4)(5) (2)(3)(4) 38 kHz TSOP4138 TSOP2138 TSOP4338 TSOP2338 TSOP4538 TSOP2538 40 kHz TSOP4140 TSOP2140 TSOP4340 TSOP2340 TSOP4540 TSOP2540 56 kHz TSOP4156 TSOP2156 TSOP4356 TSOP2356 TSOP4556 TSOP2556 Package Mold 1 = OUT, 1 = OUT, 1 = OUT, 1 = OUT, 1 = OUT, 1 = OUT, Pinning 2 = GND, 3 = V 2 = V , 3 = GND 2 = GND, 3 = V 2 = V , 3 = GND 2 = GND, 3 = V 2 = V , 3 = GND S S S S S S Dimensions (mm) 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical filter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 5 V I 0.55 0.7 0.9 mA v S SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - deg 1/2 Rev. 2.0, 14-Dec-2021 Document Number: 82460 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000