TSOP581.., TSOP583.., TSOP585.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V 1 Suitable for short bursts: burst length 6 carrier 22 cycles 33 19026 Improved immunity against ambient light Insensitive to supply voltage ripple and noise click logo to get started DESIGN SUPPORT TOOLS Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 Models Available DESCRIPTION MECHANICAL DATA These products are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are Pinning for TSOP581.., TSOP583.., TSOP585: assembled on a lead frame, the epoxy package contains an 1 = OUT, 2 = GND, 3 = V S IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP583.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. They may suppress some data signals if continuously transmitted. The TSOP581.. series devices are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP583.. series containing the newer AGC3. The TSOP585.. series are useful to suppress even extreme levels of optical noise, but may also suppress some data signals. Please check compatibility with your codes. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY PRODUCT FOR NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS AGC SHORT BURST REMOTE SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) CONTROLS (AGC1) 30 kHz TSOP58130 TSOP58330 TSOP58530 33 kHz TSOP58133 TSOP58333 TSOP58533 (1) 36 kHz TSOP58136 TSOP58336 TSOP58536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP58138 TSOP58338 TSOP58538 40 kHz TSOP58140 TSOP58340 TSOP58540 56 kHz TSOP58156 TSOP58356 TSOP58556 Package Minicast Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Rev. 1.6, 26-Sep-2018 Document Number: 82462 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP581.., TSOP583.., TSOP585.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833 14 17170-11 R 1 3 Transmitter IR receiver with V 33 k + V S S TSALxxxx C 1 1 C OUT Band Demo- Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S 5mA Output current I O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, IR diode TSAL6200, I = 50 mA, v F Transmission distance d- 18 - m test signal see Fig. 1 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E -0.2 0.4 mW/m e min. t - 5/f < t < t + 6/f test signal see Fig. 1 pi o po pi o, 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 0.5 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, N = 6 pulses, f = f , t = 10 ms) F 0 = 950 nm, optical test signal, Fig. 1 0.4 t t *) 0.3 pi Output pulse width T 0.2 *) t 6/f is recommended for optimal function pi 0 Input burst length Output Signal 14337 0.1 V O 1) 3/f < t < 9/f 0 d 0 2) t - 4/f < t < t + 6/f V pi 0 po pi 0 OH 0 0.1 10 1000 100 000 V OL 1) 2) t t t d po 2 E - Irradiance (mW/m ) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.6, 26-Sep-2018 Document Number: 82462 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit