TSOP753..W, TSOP755..W www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Compatible also with short burst dataformats Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Capable of side or top view Low profile 2.35 mm Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 DESCRIPTION click logo to get started DESIGN SUPPORT TOOLS The TSOP753..W, TSOP755..W series are a miniaturized receiver module for infrared remote control systems. Two PIN diodes and a preamplifier are assembled on a Models Available leadframe, the epoxy package contains an IR filter. The TSOP753..W..series is optimized to suppress almost all MECHANICAL DATA spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously Pinning: transmitted. 1, 4 = GND, 2 = V , 3 = OUT S The TSOP755..W series contain a very robust AGC5. This series should only be used for critically noisy environments. ORDERING CODE This component has not been qualified according to Taping: automotive specifications. TSOP75...WTT - top view taped TSOP75...WTR - side view taped PARTS TABLE NOISY ENVIRONMENTS VERY NOISY ENVIRONMENTS AGC AND SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP75330W TSOP75530W 33 kHz TSOP75333W TSOP75533W (1) 36 kHz TSOP75336W TSOP75536W Carrier (2)(3)(4)(5) frequency 38 kHz TSOP75338W TSOP75538W 40 kHz TSOP75340W TSOP75540W 56 kHz TSOP75356W TSOP75556W Package Heimdall no lens Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 3.0 H x 2.35 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 Rev. 1.9, 04-Jun-2018 Document Number: 82497 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP753..W, TSOP755..W www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170-11 2 R 1 V Transmitter S IR receiver 30 k with V + V S S 3 TSALxxxx C 1 OUT Band Demo- C Input AGC OUT pass dulator V O 1, 4 GND GND PIN GND Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH E = 0, test signal see Fig. 1, IR diode TSAL6200, v Transmission distance d- 16 - m I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.25 0.5 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 75 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 0.40 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, N = 6 pulses, f = f , t = 10 ms) F 0 0.35 0.30 t Output pulse width 0.25 t *) pi 0.20 T *) t 6/f is recommended for optimal function 0.15 pi 0 Input burst length Output Signal 14337 0.10 V O 1) 3/f < t < 9/f 0 d 0 0.05 = 950 nm, 2) t - 4/f < t < t + 6/f pi 0 po pi 0 optical test signal, Fig. 1 V OH 0 0.1 1 10 100 1000 10 000 V OL 1) 2) t t t 20760 d po E - Irradiance (mW/m) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.9, 04-Jun-2018 Document Number: 82497 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit