VJ1210A470JXGAT5Z Vishay

VJ HVArc Guard www.vishay.com Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors Prohibit Surface Arc-Over in High-Voltage Applications FEATURES For this Worldwide Patented Technology Specialty: high-voltage applications MLCC that protects against surface arc-over Excellent high-voltage performance Higher capacitances and smaller case sizes that save board space, as compared to standard Available high-voltage MLCCs Voltage breakdowns as much as twice that of competitors products Available with polymer termination for increase resistance to board flex cracking. Please contact factory for availability Wet build process Reliable Noble Metal Electrode (NME) system Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS Power supplies DC/DC converters (buck and boost) Voltage multipliers for flyback converters For lighting and other AC applications please contact: mlcc vishay.com ELECTRICAL SPECIFICATIONS C0G (NP0) X7R GENERAL SPECIFICATION GENERAL SPECIFICATION Note Note Electrical characteristics at +25 C unless otherwise specified Electrical characteristics at +25 C unless otherwise specified Operating Temperature: -55 C to +125 C Operating Temperature: -55 C to +125 C Capacitance Range: 10 pF to 8.2 nF Capacitance Range: 220 pF to 270 nF Voltage Range: 1000 V to 2500 V Voltage Range: 250 V to 1000 V DC DC DC DC Temperature Coefficient of Capacitance (TCC): Temperature Coefficient of Capacitance (TCC): 0 ppm/C 30 ppm/C from -55 C to +125 C 15 % from -55 C to +125 C, with 0 V applied DC Dissipation Factor (DF): Dissipation Factor (DF): 0.1 % maximum at 1.0 V and 2.5 % maximum at 1.0 V and 1 kHz RMS RMS 1 MHz for values 1000 pF Insulating Resistance: 0.1 % maximum at 1.0 V and RMS at +25 C 100 000 M min. or 1000 F whichever is less 1 kHz for values > 1000 pF at +125 C 10 000 M min. or 100 F whichever is less Insulating Resistance: Aging Rate: 1 % maximum per decade at +25 C 100 000 M min. or 1000 F whichever is less at +125 C 10 000 M min. or 100 F whichever is less Dielectric Strength Test: performed per method 103 of EIA 198-2-E. Aging Rate: 0 % maximum per decade Applied test voltages Dielectric Strength Test: 250 V -rated: 200 % of rated voltage DC performed per method 103 of EIA 198-2-E. 500 V -rated: min. 150 % of rated voltage DC Applied test voltages 630 V , 1000 V -rated: min. 120 % of rated voltage DC DC 1000 V -rated: 150 % of rated voltage DC 1500 V , 2500 V -rated: 120 % of rated voltage DC DC Revision: 25-May-2018 Document Number: 45197 1 For technical questions, contact: mlcc vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 VJ HVArc Guard www.vishay.com Vishay Vitramon QUICK REFERENCE DATA CAPACITANCE MAXIMUM VOLTAGE DIELECTRIC CASE (V) MINIMUM MAXIMUM 0805 1500 10 pF 390 pF 1206 1500 10 pF 1.5 nF C0G (NP0) 1210 1500 10 pF 2.7 nF 2220 1500 470 pF 5.6 nF 2225 2500 470 pF 8.2 nF 0805 1000 470 pF 3.3 nF 1206 1000 220 pF 47 nF X7R 1210 1000 220 pF 82 nF 1808 1000 220 pF 100 nF 1812 1000 220 pF 270 nF Note Detail ratings see Selection Chart (4) ORDERING INFORMATION (2) VJ0805 A 101 J X G A T 5Z CASE DIELECTRIC CAPACITANCE CAPACITANCE TERMINATION DC MARKING PACKAGING PROCESS (5) CODE NOMINAL TOLERANCE VOLTAGE CODE (1) CODE RATING 0805 A = C0G Expressed in J = 5 % X = Ni barrier P = 250 V A = 5Z = HVArc 1206 (NP0) picofarads (pF). K = 10 % 100 % matte tin E = 500 V unmarked Guard 1210 Y = X7R The first two M = 20 % plate finish L = 630 V (3) 1808 digits are F, E = AgPd G = 1000 V 1812 significant, the B = polymer R = 1500 V 2220 third is a 100 % matte tin O = 2500 V (4) 2225 multiplier. plate finish Examples T = 7 reel / plastic tape 102 = 1000 pF R = 11 1/4 / 13 reel / plastic tape 223 = 22 000 pF Notes (1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance. Consult for questions: mlcc vishay.com (2) Process code has to be added (3) Termination code E is for conductive epoxy assembly, contact mlcc vishay.com for availability (4) Please contact factory for polymer termination availability (5) Other termination options contact mlcc vishay.com for availability ENVIRONMENTAL STATUS TERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN X Ni barrier 100 % tin plated matte finish Yes Yes EAgPd Yes Yes B Polymer layer, 100 % tin plated matte finish Yes No FAgPd Yes No Revision: 25-May-2018 Document Number: 45197 2 For technical questions, contact: mlcc vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000