LITEPIPE MOISTURE SEALED LITEPIPE ASSEMBLY SPECIFICATIONS MATERIAL LITEPIPE - Acrylic (Clear optical grade) CLIPLITE Lens - Polycarbonate, Seal - J-Von Retaining Ring - Polypropylene (black) (U.L. Listed Materials) DESIGN Low profile lens assembly with moisture seal and LITEPIPE . MOUNTING Mounts in .281 (7.2mm) hole on 3/8 centers. Panel thickness 1/32 to 1/8. Compression of the seal is accomplished by pressing the retaining ring into place. STANDOFF Use standoff to adjust height of standard LED above the PCB in order to maintain a maximum .050 clearance between LITEPIPE and LED. See STD Series data sheet on page 28. U.S. & Foreign Patents Issued and Pending VERSATILITY The LITEPIPE assembly provides a method of transmitting the light from PCB mounted LEDs to the front display panel while providing moisture protection. Both styles of LEDs, surface mount, 3mm APPLICATION and 5mm standard packages can be displayed in this manner. BRIGHTNESS LITEPIPE increases the apparent brightness and viewing angle of a PCB mounted LED. LITEPIPE transmits the light from the source to the lens, which in turn disperses the light up to 180 degrees. GAP .050 APPLICATION The LITEPIPE assembly meets NEMA 3 conditions for moisture and dust. Because there is no physical connection between the lightpipe and PCB mounted LED, the circuit board can be installed or removed without disturbing the panel display. INSTALLATION The LITEPIPE and CLIPLITE lens assembly is easily installed. Pass assembly through the panel Pass lens through panel opening. Press on retaining ring. Air gap .050 maximum between opening and press on retaining ring to secure unit to the panel. Slide PCB into position aligning LED LED and LITEPIPE . Use standoff to adjust LED height. with the end of the LITEPIPE unit. PANEL ASSEMBLY ORDERING CODES LMS XXX RTP MODEL COLOR Assembly contains CLIPLITE Lens, RTP Red Transparent LITEPIPE , and retainer. ATP Amber Transparent GTP Green Transparent BTP Blue Transparent YTP Yellow Transparent LITEPIPE CTP Clear Transparent LENGTH (INCHES) 033 (.330 ) 093 (.930 ) Hold lens tightly to panel, careful not to mar lens surface. Use 5/16 nut driver or deep socket 053 (.530 ) 113 (1.13 ) to press on retaining ring, compressing seal. 073 (.730 ) 133 (1.33 ) OUTLINE DRAWING RECOMMENDED LEDs LMS LITEPIPE /Lens Assembly RNG 268 SEE PAGE 29-31 1.800.522.5546 vccsales vcclite.com www.VCCLITE.com 9X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for LED Light Pipes category: Click to view products by Visual Communications manufacturer: Other Similar products are found below : 1367627-1 SLP3-300-450-F SLP3-400-450-R LPA-C011301S-23 LPA-C011301S-6 LPF-C011306S 515-1061-803F 515-1142-170F 515- 1155F VLP-640-F LMC-034-CTP LPA-C011301S-5.4 LPA-C041301S-2 LPA-S011331S LPC 155 CTP LPC 182 CTP LPC 190 CTP 515-1001-802F 515-1027-803F 515-1048-801F 515-1142-195F 515-1146F 515-1148F 515-1217F SLP3-150-300-R SLP3-500-450-R 515- 1058F 515-1064-810F 515-1114-801F FLPR-SBC FLPV-SG FLPR-SG BDL-1187 7511A41 7511A62V0 7511F2 FLPV-SBC SLP3-300- 250-R 5151064802F LPF-R011340S 515-1166-801F FLPF-6.0 SLP3-350-200-F LC-11.25 CLP-1214 1296.2044 515-1064-808F FLX3 05 515-1192-0025-0DF 515-1192-80-3DF