734-264 Wago

Male Headers with Solder and Press-In Pins, MCS-MIDI 4 Pin Spacing: 3.5 mm, 3.81 mm 250 MCS MINI Male header s may be mounted horizontally or vertically via straight or angled solder pins 1 x 1 mm pin cr oss section (MCS MINI) allows a nominal current of 10 A Double-deck male headers save space on the PCB, providing a large number of wire-to-board connections 100% pr otected against mismating Coding pins av ailable Press-in technology: Double-deck version: Technical data: 3.5/3.81 mm 3.5/3.81 mm 3.5/3.81 mm Pin Spacing Derating Curve 0.138 in. 0.138 in. 0.138 in. 734-102 female connector with 734-162 male header Ratings per IEC/EN 60664-1 IEC/EN 60664-1 IEC/EN 60664-1 2 Pin spacing: 3.5 mm / Conductor size: 1.5 mm f-st Overvoltage category III III II III III II III III II Based on: EN 60512-5-2 / Reduction factor: 0.8 Pollution degree 3 2 2 3 2 2 3 2 2 Current in A Rated voltage 160 V 160 V 320 V 160 V 160 V 320 V 160 V 160 V 320 V Rated surge voltage 2.5 kV 2.5 kV 2.5 kV 2.5 kV 2.5 kV 2.5 kV 2.5 kV 2.5 kV 2.5 kV 20 Nominal current 10 A 10 A 10 A 8 A 8 A 8 A 10 A 10 A 10 A Approvals per UL/CSA UL/CSA UL/CSA 15 Use group UL 1059 B C D B C D B C D Rated voltage 300 V 300 V 300 V 300 V 300 V 300 V 10 Nominal current UL 10 A 10 A 10 A 10 A 10 A 10 A Nominal current CSA 10 A 10 A 10 A 10 A 10 A 10 A 5 Solder and press-in pin data: 0 10 20 30 40 50 60 70 80 90 100 105 Solder pin: length/width 4.5 mm / 1 x 1 mm (straight) Solder pin: length/width 3.8 mm / 1 x 1 mm (angled) Ambient operating temperature in C Solder pin: length/width 3.6 mm / 1 x 1 mm (double-deck male headers) 2-, 4-, 6-, 12-, 24-pole Conductor rated current +0.1 Solder pin: drilled hole diameter 1.4 mm Press-in pin: length/width 2.9 mm / 0.6 x 1.2 mm 0,025 Press-in pin: drilled hole diameter 1,15 Press-in pin: metal-plated hole 1.0 0.06 mm (HAL Sn) Press-in pin: metal-plated hole 1.0 0.00 mm (Chem. Sn) For other pin lengths, please contact factory. Material data: MCS MINI accessory: Page: Material group I Insulating material Polyamide 66 (PA 66) Coding keys 273 Flammability class per UL 94 V0 Lower/Upper limit temperature -60 C / +100 C / Press-in pin: -40 C / +85 C Contact material Electrolytic copper (E ) / Copper alloy for press-in technology Cu Contact plating tin-plated MCS connectors are also available upon request with gold-plated or partially gold-plated contact surfaces. Depending on the version requested, item no. suffix . /010-000 is added to the basic item no. The MULTI CONNECTION SYSTEM (MCS) is designed without breaking capacity for compliance with DIN EN 61984. When used as intended, these connectors shall not be connected/disconnected when live or under load. The circuit design should ensure header pins, which can be touched, are not live when unmated. Additional approvals and corresponding ratings can be found at www.wago.com. For additional technical information, see Section 13.X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for wago manufacturer: Other Similar products are found below : 750-460 231-118/026-000 231-303/026-000 231-620/019-000 257-403 280-438 280-831 284-624 210-111 231-303/037-000 231-446/001- 000 NR 232-216/026-000 234-510 264-726 280-339 0283-0671 830-800/000-305 750-512 750-455 51251782 286-312 713-1428/107-000 731-138/048-000 750-459 750-517 793-3505 826-172 859-304 280-335 231-535/001-000 2604-1106 2604-1504 2606-1103/020-000 2624- 1103 2626-3103/020-000 821-104 713-1107 852-1411 2106-1307 2116-5307 832-1205 832-3604 2009-110 281-512/281-501 286-336 750-421 750-838 753-559 750-1505 787-732