MKS0D031000C00KO00 WIMA

D WIMA MKS 02 Metallized Polyester (PET) Capacitors in PCM 2.5 mm. Capacitances from 3300 pF to 1.0 mF. Rated Voltages from 50 VDC to 250 VDC. Special Features Electrical Data High volume/capacitance ratio Capacitance range: Dissipation factors at + 20) C: tan d and reduced base 3300 pF to 1.0 mF (E12-values on request) at f C 0.1 mF 0.1 mF P C 1.0 mF PCM 2.5 mm Rated voltages: -3 -3 1 kHz 8 x 10 8 x 10 Self-healing 50 VDC, 63 VDC, 100 VDC, 250 VDC -3 -3 10 kHz 15 x 10 15 x 10 According to RoHS 2011/65/EU Capacitance tolerances: -3 100 kHz 30 x 10 20%, 10% (5% available subject to special enquiry) Voltage derating: Typical Applications Operating temperature range: A voltage derating factor of 1.25 % per K 55+ C to +100+ C must be applied from +85+ C for DC For general DC-applications e.g. Test specifications: voltages and from +75+ C for AC By-pass In accordance with IEC 60384-2 voltages. Blocking Climatic test category: Reliability: Coupling and decoupling 55/100/21 in accordance with IEC Operational life 300 000 hours Timing Insulation resistance at +20+ C: Failure rate P 2 fit (0.5 x U and 40) C) r Construction U U C 0.33 mF 0.33 mF < C 1.0 mF r test 3 3.75 x 10 M 1250 sec (M x mF) 50 VDC 10 V Dielectric: 4 (mean value: 1 x 10 M) (mean value: 3000 sec) Polyethylene-terephthalate (PET) film 3 3.75 x 10 M 1250 sec (M x mF) Capacitor electrodes: 63 VDC 50 V 4 (mean value: 1 x 10 M) (mean value: 3000 sec) Vacuum-deposited 4 Internal construction: 1 x 10 M 100 VDC 100 V 4 (mean value: 2 x 10 M) Measuring time: 1 min. Plastic film Test voltage: 1.6 U , 2 sec. r Vacuum-deposited Maximum pulse rise time: electrode Metal contact layer (schoopage) Capacitance Pulse rise time V/msec Terminating wire pF/mF max. operation/test 3300 ... 6800 100 / 1000 0.01 ... 0.022 50 / 500 0.033 ... 0.068 30 / 300 0.1 ... 0.33 20 / 200 Encapsulation: 0.47 ... 1.0 15 / 150 Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 for pulses equal to the rated voltage Terminations: Tinned wire. Marking: Mechanical Tests Packing Colour: Red. Marking: Silver. Epoxy resin seal: Yellow Pull test on pins: Available taped and reeled. 10 N in direction of pins according to IEC 60068-2-21 Detailed taping information and graphs Vibration: at the end of the catalogue. 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 2 4000 bumps at 390 m/sec in For further details and graphs please accordance with IEC 60068-2-29 refer to Technical Information. 29 01.16D WIMA MKS 02 Continuation General Data 50 VDC/30 VAC* 63 VDC/40 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 0.01 mF 2.5 7 4.6 2.5 MKS0C021000B00 0.015 2.5 7 4.6 2.5 MKS0C021500B00 0.022 2.5 7 4.6 2.5 MKS0C022200B00 0.033 2.5 7 4.6 2.5 MKS0C023300B00 0.047 2.5 7 4.6 2.5 MKS0C024700B00 0.068 2.5 7 4.6 2.5 MKS0C026800B00 0.1 mF 3 7.5 4.6 2.5 MKS0C031000C00 0.15 3 7.5 4.6 2.5 MKS0C031500C00 0.22 3 7.5 4.6 2.5 MKS0C032200C00 0.33 3.8 8.5 4.6 2.5 MKS0C033300D00 0.47 4.6 9 4.6 2.5 MKS0C034700E00 0.68 5.5 10 4.6 2.5 MKS0C036800F00 1.0 mF 5.5 10 4.6 2.5 MKS0B041000F00 100 VDC/63 VAC* 250 VDC/160 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 3300 pF 2.5 7 4.6 2.5 MKS0F013300B00 4700 2.5 7 4.6 2.5 MKS0F014700B00 6800 2.5 7 4.6 2.5 MKS0F016800B00 0.01 mF 2.5 7 4.6 2.5 MKS0D021000B00 2.5 7 4.6 2.5 MKS0F021000B00 0.015 2.5 7 4.6 2.5 MKS0D021500B00 2.5 7 4.6 2.5 MKS0F021500B00 0.022 2.5 7 4.6 2.5 MKS0D022200B00 2.5 7 4.6 2.5 MKS0F022200B00 0.033 2.5 7 4.6 2.5 MKS0D023300B00 3 7.5 4.6 2.5 MKS0F023300C00 0.047 2.5 7 4.6 2.5 MKS0D024700B00 3.8 8.5 4.6 2.5 MKS0F024700D00 0.068 2.5 7 4.6 2.5 MKS0D026800B00 4.6 9 4.6 2.5 MKS0F026800E00 0.1 mF 3 7.5 4.6 2.5 MKS0D031000C00 5.5 10 4.6 2.5 MKS0F031000F00 0.15 3.8 8.5 4.6 2.5 MKS0D031500D00 0.22 4.6 9 4.6 2.5 MKS0D032200E00 0.33 5.5 10 4.6 2.5 MKS0D033300F00 * AC voltage: f = 50 Hz 1.4 x U + UDC U rms r ** PCM = Printed circuit module = pin spacing Dims. in mm. W L Part number completion: H d = 0.4 l Tolerance: 20 % = M 10 % = K 6 -2 5 % = J d Packing: bulk = S 2.5 PCM Pin length: 6-2 = SD at the pin exit points (0 .5) Taped version see page 143. Impedance change with frequency (general guide). Rights reserved to amend design data without prior notification. 30 01.16