Dimensions: mm Drillhole specification for PCB: Properties: Properties Value Unit Tol. Drill hole specification for chemical surfaces detail B Material Brass Surface Tin (O 1,60 -0,03 ) min. 0,10 Execution Press-Fit O 1,475 0,05 Tightening Torque 0.5 Nm Operating Temperature -55 C up to +150 C 2,54 Storage Conditions 0 C up to +40 C, < 75% RH Insertion Force 40 N per Pin min. sectional drawing A-A Extraction Force 1) 30 N per Pin min. M 3 PCB Thickness min 1.6 mm A PCB Thickness max 3.2 mm min. 25m copper max. 60m 1) min. 24hours after Press-Fit Process Electrical Properties: Properties Test conditions Value Unit Tol. Drillhole specification for PCB: Rated Current 20 C I 70 A max. R Drill hole specification for HAL B (O 1,60 -0,03 ) min. 0,10 Packaging Properties: A O 1,45 0,05 Packaging Bulk max. 15m Sn min. 25m copper max. 60m Scale - 3:1 CREATED CHECKED GENERAL TOLERANCE PROJECTION Wrth Elektronik eiSos GmbH & Co. KG METHOD EMC & Inductive Solutions DaMa WlW DIN ISO 2768-1m Max-Eyth-Str. 1 DESCRIPTION 74638 Waldenburg Germany REDCUBE PRESS-FIT with internal Tel. +49 (0) 79 42 945 - 0 ORDER CODE thread and full plain pin-plate WP- www.we-online.com 7462810 BUFU eiSos we-online.com REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE 001.002 Valid 2017-10-19 eiCan 1/3 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Wrth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Wrth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. q 5,0 10,5 2,54 Bevelled edge 0,3 0,2 around 4,0 3,5 0,2 7,0Cautions and Warnings: The following conditions apply to all goods within the product series of WP-BUFU of Wrth Elektronik eiSos GmbH & Co. KG: General: All recommendations according to the general technical specifications of the data-sheet have to be complied with. The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. Product Specific: Follow all instructions in the datasheet, especially: Drill-hole specifications. Wave and reflow soldering is not applicable. The maximum permissible torques must be complied with to prevent mechanical destruction. While press-fit process PCB should be supported against bending. Chip formation due to material displacement is permitted. CREATED CHECKED GENERAL TOLERANCE PROJECTION Wrth Elektronik eiSos GmbH & Co. KG METHOD EMC & Inductive Solutions DaMa WlW DIN ISO 2768-1m Max-Eyth-Str. 1 DESCRIPTION 74638 Waldenburg Germany REDCUBE PRESS-FIT with internal Tel. +49 (0) 79 42 945 - 0 ORDER CODE thread and full plain pin-plate WP- www.we-online.com 7462810 BUFU eiSos we-online.com REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE 001.002 Valid 2017-10-19 eiCan 2/3 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Wrth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Wrth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
