316-1.8K/REEL-RC Xicon

5% High Power Thick Film Resistors HP5-RC Series (RoHS Compliant) FEATURES Temperature Range:-55C ~ +155C (derated over 70C) Value Range: 1~10M Wave or Flow Solderable DERATING CURVE -55C +70C +155C 100 80 60 40 20 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 Ambient Temperature (C) PART NUMBERING SYSTEM 1 0 K E L 3 1 4 - - R E - R C Suffix Series Package Value (RoHS Compliant) SERIES, SIZE, WATTAGE, VOLTAGE, AND DIMENSIONS L C C L W W H H D D Voltage (V) (max.) Dimension (mm) Series Case Size Watts (W) W.V. O.V. L W H C D 314 0603 1/5 50 100 1.60.10 .80.10 .45.10 .30.20 .30.20 316 0805 1/3 75 150 2.00.15 1.25.15 .55.10 .40.20 .40.20 318 1206 1/2 200 400 3.10.15 1.55.15 .55.10 .45.20 .45.20 320 2512 2 250 500 6.35.10 3.20.20 .55.10 .60.25 .50.20 STANDARD VALUES () 1.0 15 56 180 470 1.5K 4.7K 22K 56.2K 330K 1.5 18 68 200 510 1.8K 5.6K 27K 82K 390K 2.7 22 75 220 560 2.0K 6.8K 33K 100K 470K 4.7 27 82 270 620 2.2K 8.2K 36K 120K 560K 7.5 33 100 300 680 2.7K 10K 39K 150K 680K 8.2 39 120 330 820 3.0K 12K 47K 180K 820K 10 47 150 360 1.0K 3.3K 15K 51K 220K 1.0M 12 51 160 390 1.2K 3.9K 18K 56K 270K 10M XICON PASSIVE COMPONENTS (800) 628-0544 XC-600247 Date Revised: 10/29/19 Specifications are subject to change without notice. No liability or warranty implied by this information. Environmental compliance based on producer documentation. Percent Rated Load (%)5% High Power Thick Film Resistors HP5-RC Series (RoHS Compliant) CHARACTERISTICS Test Methods Characteristics Limits (JIS C 5201-1) 4.7 Clamped in the trough of a 90C metallic v-block and shall be tested at ac potential respectively specified in the type for 60-70 seconds Dielectric No evidence of flashover withstanding mechanical damage, arcing or insulation voltage break down 4.8 Natural resistance change per temp. degree centigrade. R2-R1 6 Temperature 1~10200PPM/C x 10 (PPM/C) Coefficient 10.1~10M100PPM/C R1(t2-t1) R1: Resistance value at room temperature (T1) R2: Resistance value at room tem. plus 100C(T2) Test pattern: room temp. (T1), room temp. +100C(T2) 4.13 Permanent resistance change after the application of a potential of 2.5 times RCWV for 5 seconds Resistance change rate is Short time 5% (2.0% + 0.1) Max. overload 1% (1.0% + 0.1) Max. Wave Solder: Test temperature of solder: 245C3C dipping time in solder: 2-3 seconds. Reflow: VALUE TEMPERATURE: 245C -250C 250 230C Solderability 95% coverage Min. 200 WARM-UP TIME 180C 150 150C 9030s 100 2010s 50 SOLDER TIME HOT UP TIME 4.18 Dip the resistor into a solder bath having a temperature of Resistance change rate is 260C3C and hold it for 101 seconds Soldering heat + (1.0% + 0.05) Max. 4.19 Resistance change after continiuous 5 cycles for duty cycle specified below: Step Temperature Time Resistance change rate is Temperature 1 -55C 3C 30 mins 5% (2.0% + 0.05) Max. Cycling 1% (0.5% + 0.05) Max. 2 Room temp. 10~15 mins 3 +155C 2C 30 mins 4 Room temp. 10~15 mins XICON PASSIVE XICON PASSIVE COMPONENTS (800) 628-0544COMPONENTS (800) 628-0544 XC-600247 Date Revised: 10/29/19 Specifications are subject to change without notice. No liability or warranty implied by this information. Environmental compliance based on producer documentation.