HW-USB-II-G Xilinx

36 Platform Cable USB II DS593 (v1.5.1) August 6, 2018 Features High-performance FPGA and PROM programming and Reliable configuration Backwards compatibility with Platform Cable USB, Includes innovative FPGA-based acceleration including Pb-Free (RoHS-compliant) firmware encapsulated in a small form factor pod USB Integrators Forum (USB-IF) certified attached to the cable CE and FCC compliant Leverages high-speed slave-serial mode Leverages industry standards, including JTAG programming interface boundary-scan IEEE 1149.1, SPI and USB 2.0 Note: Slave-serial mode is supported in Xilinx Programs and configures all Xilinx devices iMPACT software v10.1. XC18V00 ISP PROMs Recommended for prototyping use only Platform Flash XCF00S/XCF00P/XL PROMs Easy to use All UltraScale, 7 series, Virtex, and Spartan Fully integrated and optimized for use with Xilinx FPGA families, and Zynq-7000 SoCs iMPACT software XC9500XL and CoolRunner XPLA3 / Intuitive multiple cable management from a single CoolRunner-II CPLDs application Note: Xilinx iMPACT software or Vivado design tools Supported on the following operating systems: are required for programming and configuration. See the Note: See the Xilinx design tool release notes for design tool release notes for supported devices. supported operating systems. Third-party PROM device programming support - Microsoft Windows XP Professional Directly programs selected Serial Peripheral - Microsoft Windows Vista Interface (SPI) flash memory devices - Red Hat Enterprise Linux Note: Direct SPI flash memory programming supported in Xilinx iMPACT software v10.1. - SUSE Linux Enterprise Indirectly programs selected SPI or parallel flash Automatically senses and adapts to target I/O memory devices via FPGA JTAG port voltage Highly optimized for use with Xilinx design tools Interfaces to devices operating at 5V (TTL), 3.3V (LVCMOS), 2.5V, 1.8V and 1.5V Vivado design tools or ISE design tools Intuitive flyleads-to-cable interface labeling Embedded Development Kit ChipScope Pro Analyzer System Generator for DSP Platform Cable USB II Description Much more than just a simple USB cable, Platform Cable PROMs and CPLDs, and directly programming third-party USB II (Figure 1) provides integrated firmware (hardware SPI flash devices. In addition, the cable provides a means of and software) to deliver high-performance, reliable and indirectly programming Platform Flash XL, third-party SPI easy-to-perform configuration of Xilinx devices. flash memory devices, and third-party parallel NOR flash memory devices via the FPGA JTAG port. Furthermore, Platform Cable USB II attaches to user hardware for the Platform Cable USB II is a cost effective tool for debugging purpose of configuring Xilinx FPGAs, programming Xilinx Copyright 20082018 Xilinx, Inc. Xilinx, the Xilinx logo, Artix, ISE, Kintex, Spartan, Virtex, Vivado, Zynq, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respective owners. DS593 (v1.5.1) August 6, 2018 www.xilinx.com PN 0011051 04 1Platform Cable USB II embedded software and firmware when used with applications such as Xilinx s Embedded Development Kit and ChipScope Pro Analyzer. Platform Cable USB II is an upgrade to and replaces Platform Cable USB. Similar to its popular predecessor, Platform Cable USB II is intended for prototyping environments only. Platform Cable USB II is backwards Compatible with Platform Cable USB and is supported by all Xilinx design tools that support Platform Cable USB. Platform Cable USB II attaches to the USB port on a desktop or laptop PC using an off-the-shelf Hi-Speed USB AB cable. The cable derives all operating power from the hub port controller no external power supply is required. Note: Sustained data transfer rates in a Hi-Speed USB environment vary according to the number of USB devices sharing the hub bandwidth. Native signaling rate (480 MHz) is not directly correlated to application throughput. Device configuration and programming operations using Platform Cable USB II are supported by Xilinx iMPACT download software using boundary-scan (IEEE 1149.1/IEEE 1532), slave-serial mode, or serial peripheral interface (SPI). The Vivado design tools support device configuration with the Platform Cable USB II using boundary-scan (IEEE 1149.1). Note: iMPACT software is bundled with the ISE design tools and WebPACK ISE software. The slave-serial mode and direct SPI are only supported in limited versions of the ISE iMPACT tool. In addition, Platform Cable USB II is optimized for use with the Xilinx Embedded Development Kit, ChipScope Pro Analyzer, and System Generator for DSP. When used with these software tools, the cable provides a connection to embedded target systems for hardware configuration, software download, and real-time debug and verification. Target clock speeds are selectable from 750 kHz to 24 MHz. Platform Cable USB II attaches to target systems using a 14-conductor ribbon cable designed for high-bandwidth data transfers. An optional adapter for attaching a flying lead set is included for backward compatibility with target systems not using a ribbon cable connector. X-Ref Target - Figure 1 DS593 01 021408 Figure 1: Xilinx Platform Cable USB II DS593 (v1.5.1) August 6, 2018 www.xilinx.com 2