DC-HVDC Converter A Series 1 & 1.5 Watt Output voltages from 100V to 6000V xxx Series Output Proportional to Input 0.7VDC Turn-on Voltage Extremely Low Profile <0.25 Input to Output Isolation Short Circuit Protection Control Pin No minimum load 3 Year Warranty Dimensions: All models: The A Series is a broad line of ultra-miniature, DC to HV DC converters that set an industry Height x Width: 0.25 x 0.45 (6.35 x 11.43mm) standard in high voltage miniaturization. This unique package occupies less than one tenth of a cubic inch of volume, and an extremely low profile of only 0.250 inches (6.35mm). 100V to 2000V outputs: 6000V outputs: Length: 1.33 (33.78mm) Length: 0.92 (23.37mm) Controllable output voltages range from 100 volts to 6000 volts. The output is directly 3000V to 5000V outputs: proportional to the input voltage and is linear from <0.7V input to maximum input voltage, Length: 1.13 (28.69mm) allowing for an adjustable output voltage. Output is load dependent. Isolation permits <500V bias on output return. No external components or minimum load are required. Key Applications: Avalanche Photo Diodes A separate high impedance control pin is standard and is designed for external error amplifier Photo Multiplier Tubes and/or DAC control in closed or open loop systems. Or simply connect the control pin to the Electrophoresis + input for proportional input to output operation. These component-sized converters are ideal Capacitor Charging for applications requiring minimal size and weight. Sustaining Ion Pumps Piezo Devices Handheld Instruments Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage 0.7 5,12,24 VDC See Models and Ratings Table. Input Current 550 mA See Models and Ratings Table. Control Voltage Input Analog Control Voltage adjusts output from 0 to 100%, not to exceed Input Voltage, see Application Notes on Page 8 for details. Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 6,000 VDC See Models and Ratings Table Output Current 15 mA See Models and Ratings Table Output Voltage Tolerance +10, -10 % At Max Vout, Full Load Minimum Load No minimum load required Regulation Unregulated, Output is proportional to Input. See Application Notes. Short Circuit Protection Protected against short circuit conditions for a minimum 1 minute. Ripple and Noise 5 % See Models and Ratings Table. Notes 1. Maximum output current is available at maximum rated output voltage, and 3. Specifications are after 30 minute warm-up, full-load at 25C, unless otherwise derates linearly as input voltage is decreased. noted. 2. Output Voltage is load dependent. Under light or no-load conditions, reduce the 4. Proper thermal management techniques are required to maintain safe case Input Voltage so maximum rated Output Voltage is not exceeded. temperature at maximum power output. www.xppower.com 1DC-HVDC Converter A Series Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature (case) -25 +75 C Standard operating temp, all models Operating Temperature (case) -55 +85 C Extended operating temp, -T models Storage Temperature -55 +105 C Humidity 95 %RH Non-condensing Cooling Natural Convection Safety Approvals Safety Agency Safety Standard Notes & Conditions UL IEC/UL/CSA/EN 62368 CE CE Directive, RoHs and LVD Where applicable RoHS RoHS 2 and 3 Directive (2011/65/EU) Where applicable General Characteristic Minimum Typical Maximum Units Notes & Conditions Isolation: Input to Output 500 V < 500 VDC Bias on Output Return Leakage Current 100 nA Switching Frequency 50 350 kHz Construction Solid vacuum encapsulation, UL 94 V-0 rated. Mean Time Between Failure 1.862 MHrs Per Bellcore TR 332 Block Diagram Pin Connections Pin Function 1 (-) Input 2 (+) Input 3 HV Out 4 HV RTN 5 Control www.xppower.com 2