125 Watts xppower.com CLC Series 125 W Forced-cooled Rating Low Profile 1.25 Industry Standard 2x 4& 3x 5Package Sizes 12 V Fan Supply Optional ORing Diode <0.5 W No Load Input Power 3 Year Warranty Specification Input General Input Voltage 85-264 VAC (120-370 VDC), Efficiency 88% typical Derate output power linearly to 90% from Isolation 3000 VAC Input to Output, 1500 VAC Input 90 VAC to 85 VAC to Ground, 500 VDC Output to Ground Input Frequency 47-63 Hz Switching Frequency 65 KHz typical Input Current 2.3 A typical at 115 VAC, full load MTBF 1,245 KHrs to Telecordia SR-332 1.1 A typical at 230 VAC, full load at 25 C, GB Inrush Current 40 A max at 230 VAC, cold start 25 C Power Factor EN61000-3-2, class A Environmental No Load Input Power <0.5 W Operating Temperature 0 C to +70 C derate linearly from +50 C Earth Leakage Current 80/160 A typical 115/230 VAC 50 Hz at 2.5%/C to 50% load at +70 C. 300 A at 264 VAC/60 Hz max. Cooling Forced cooled, 10 CFM Input Protection Internal T5 A/250 V fuse in line Operating Humidity 95% RH, non-condensing Storage Temperature -40 C to +85 C Output Operating Altitude 3000 m Shock 30 g pk, half sine, 6 axes Output Voltage 12-48 VDC (see tables) Vibration 2 g rms, 5 Hz to 500 kHz, 3 axes Output Voltage Trim 10% Initial Set Accuracy 1% EMC & Safety Minimum Load No minimum load required Start Up Delay 1 s typical Low Voltage PSU EMC EN61204-3, high severity level as below Start Up Rise Time 50 ms Emissions EN55032 level B conducted EN55032 level A radiated Hold Up Time 16 ms min at 230 VAC Harmonic Currents EN61000-3-2, class A Drift 0.2% after 20 min warm up Voltage Flicker EN61000-3-3 Line Regulation 0.5% max Radiated Immunity EN61000-4-3, level 3 Perf Criteria A Load Regulation 1% EFT/Burst EN61000-4-4, level 3 Perf Criteria A Over/Undershoot 5% typical Surge EN61000-4-5, installation class 3 Transient Response 4% max. deviation, recovery to within Perf Criteria A 1% in 500 s for a 50-75-50% load change Conducted Immunity EN61000-4-6, level 3 Perf Criteria A Ripple & Noise 1% pk-pk V1, 20 MHz bandwidth Dips & Interruptions EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B Overvoltage Protection 115-140% Vnom, recycle input to reset Safety Approvals IEC60950-1:2005 Ed 2 / IEC62368-1:2014 Overload Protection 110-150% UL 62368-1 & CAN/CSA C22.2 Short Circuit Protection Continuous trip and restart (hiccup mode) No. 62368-1-14 Temperature 0.05%/C E N62368-1:2014/A11:2017 Coefficient Equipment Protection Class I Class AC-DCAC-DC CLC125 Models and Ratings Output Power Output Voltage V1 Output Current Fan Supply V2 Model Number 10 CFM Convection 125 W 55 W 12.0 VDC 10.4 A 12 V / 0.5 A CLC125US12 125 W 55 W 24.0 VDC 5.2 A 12 V / 0.5 A CLC125US24 125 W 55 W 48.0 VDC 2.6 A 12 V / 0.5 A CLC125US48 (1) 125 W 55 W 12.0 VDC 10.4 A 12 V / 0.5 A CLC125US12-3x5 (1) 125 W 55 W 24.0 VDC 5.2 A 12 V / 0.5 A CLC125US24-3x5 (1) 125 W 55 W 48.0 VDC 2.6 A 12 V / 0.5 A CLC125US48-3x5 (1) 125 W 55 W 12.0 VDC 10.4 A 12 V / 0.5 A CLC125US12D-3x5 (1) 125 W 55 W 24.0 VDC 5.2 A 12 V / 0.5 A CLC125US24D-3x5 (1) 125 W 55 W 48.0 VDC 2.6 A 12 V / 0.5 A CLC125US48D-3x5 Notes 1. The 3 x 5 models share the same specification as the other models except the PCB size is increased to 3 x 5 from 2 x 4. The D models have an integral output ORing diode. Mechanical Details Inp ut Connector J1 CLC125 Molex PN 09-65-2038 Pin 1 Line 4.00 (101.6) Pin 2 Neutral 1.25 (31.8) 3.750 (95.25) J1 mates with Molex housing 0.125 (3.18) p/n 09-50-1031, and Molex Voltage Adj. series 5194 crimp terminals Output Connector J2 Molex PN 09-65-2048 Pin 1 +V1 1.750 (44.45) 2.00 (50.8) Pin 2 +V1 J1 J2 Pin 3 RTN Pin 2 RTN 1.29 J2 mates with Molex housing (32.7) 1.00 (25.4) p/n 09-50-1041 and Molex 0.45 series 5194 crimp terminals J3 (11.4) Fan Supply Connector J3 Molex PN 22-04-1021 0.125 (3.18) Pin 1 Fan+ 0.29 (7.3) 0.25 Faston Pin 2 Fan- 0.20 (5.1) Gro und Tab 0.20 (5.1) 0.14 (3.5) J3 mates with Molex housing 4 X .156 (3.96) Mounting Holes SMD Component Height p/n 22-01-1024 and Molex .3 12 (7.9 2) Cle arance to p and bottom series 5103 crimp terminals CLC125 3x5 & CLC125 D 3x5 Inp ut Connector J1 5.00 (127.0) Molex PN 09-65-2038 Pin 1 Line 0.225 (5.72) 4.55 (115.57) 1.20 Pin 2 Neutral (30.5) Voltage Adj. 0.20 (5.10) J1 mates with Molex housing p/n 09-50-1031, and Molex series 5194 crimp terminals Output Connector J2 2.55 (64.77) Molex PN 09-65-2048 3.0 (76.2) Pin 1 +V1 Pin 2 +V1 Pin 3 RTN J2 Pin 2 RTN 1.79 J2 mates with Molex housing J3 1.52 (38.6) (45.4) p/n 09-50-1041 and Molex series 5194 crimp terminals 0.95 (24.1) Fan Supply Connector J3 Molex PN 22-04-1021 Pin 1 Fan+ Pin 2 Fan- 0.20 (5.1) 0.225 (5.72) 0.25 Faston 0.13 (3.2) J3 mates with Molex housing Ground Tab 0.14 (3.5) p/n 22-01-1024 and Molex 4 X .1 56 (3. 96) Mountin g H oles SMD Component Height series 5103 crimp terminals .312 (7.92) Clearance top and bottom Notes 1. All dimensions in inches (mm). 3. Tolerance .xx = 0.02 (0.50) .xxx = 0.01 (0.25) 2. Weight 0.386 lbs (175 g) 18 Feb 20