50 150 Watts xppower.com DLG Series AC Input LED Driver Constant Voltage & Current Operation High Power Factor High Efficiency Water Proof to IP67 90 305 VAC Input Voltage Range 3 Year Warranty Specification Input General Input Voltage 90-305 VAC, see derating curve Efficiency See table Input Frequency 47-63 Hz Isolation 3750 VAC Input to Output 1880 VAC Input to Ground Input Current 50 W: 1.0 A at 115 VAC, 0.5 A at 230 VAC, 500 VAC Output to Ground 75 W: 1.2 A at 115 VAC, 0.6 A at 230 VAC, 100 W: 1.4 A at 115 VAC, 0.7 A at 230 VAC, Switching Frequency DLG50/75: 40-80 kHz 150 W: 2.0 A at 115 VAC, 1.0 A at 230 VAC DLG100/150: PWM 60-80 kHz, PFC 55-133 kHz Inrush Current 65 A at 230 VAC, cold start +25 C MTBF >200 kHrs to MIL-HDBK-217F at 25 C, GB Power Factor >0.94 at 230 VAC, full load Earth Leakage Current DLG50/75: 500 A max at 230 VAC Environmental DLG100/150: 750 A max at 230 VAC No Load Input Power 0.6 W max at 230 VAC Operating Temperature DLG50/75: -40 C to +60 C Input Protection DLG50/75 T2.5A/300V fuse fitted in line, (see derating curve), DLG100 T3.15A/300V fuse fitted in line, DLG100/150: -30 C to +70 C DLG150 T4A/300V fuse fitted in line (see derating curve) Operating Humidity 5-100% RH, non-condensing Storage Temperature -40 C to +80 C Output Operating Altitude 3000 m Output Voltage See table Vibration 10-500 Hz, 2 g, 10 mins/cycle, 6 cycles in Minimum Load No minimum load required each of 3 axes Start Up Delay 1.5 s max at 115 VAC Hold Up Time DLG50/75: No hold up EMC & Safety DLG100/150: 16 ms minimum Emissions EN55015, class B conducted and radiated Line Regulation 0.5% Harmonic Currents EN61000-3-2, class A Load Regulation 1.0% in constant voltage mode, EN61000-3-2, class C for loads >80% 5.0% in constant current mode Voltage Flicker EN61000-3-3 Turn On Overshoot 5% max ESD Immunity EN61000-4-2, 8 kV air and 4 kV contact, Transient Response 5% maximum deviation, recovery to within Perf Criteria A 1% in 10 ms for a 50% load change Radiated Immunity EN61000-4-3, level 2 Perf Criteria A (1) Ripple & Noise DLG50/75 EFT/Burst EN61000-4-4, level 2 Perf Criteria A DLG100/150: 150 mV pk-pk up to 36 V Surge EN61000-4-5, installation class 3, output, 200 mV for 48 V output, 240 mV Perf Criteria A for 54 V output (see note 2) Conducted Immunity EN61000-4-6, level 2 Perf Criteria A Overvoltage Protection 110-142%, recycle mains to reset, only on DLG100 & DLG150 versions Dips & Interruptions EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Overtemperature Unit shuts down, recycle mains to reset Perf Criteria A, B, B Protection Safety Approvals EN61347, UL8750, CE Mark Overload Protection 105% maximum, auto recovery DLG100/150: IEC60950-1, EN60950-1, Short Circuit Protection Trip and restart (hiccup mode) UL60950-1 Temperature 0.04%/C Coefficient Notes 1. DLG50/75 use a topology which results in increased levels of mains frequency related ripple. Contact technical sales for details. AC DCAC DC DLG50 150 Models and Ratings Output Voltage (1) Output Power Output Voltage Output Current Range in Constant Efficiency Model Number Current Mode 50 W 12.0 V 4.20 A 8.5-12.0 V 84.0% DLG50PS12 50 W 24.0 V 2.10 A 19.0-24.0 V 86.0% DLG50PS24 50 W 36.0 V 1.40 A 26.0-36.0 V 88.0% DLG50PS36 50 W 48.0 V 1.05 A 35.0-48.0 V 88.0% DLG50PS48 59 W 12.0 V 4.90 A 8.5-12.0 V 84.0% DLG75PS12 75 W 24.0 V 3.15 A 19.0-24.0 V 86.0% DLG75PS24 74 W 30.0 V 2.45 A 22.0-30.0 V 87.0% DLG75PS30 75 W 36.0 V 2.10 A 26.0-36.0 V 88.0% DLG75PS36 67 W 48.0 V 1.40 A 35.0-48.0 V 88.0% DLG75PS48 75 W 54.0 V 1.40 A 37.0-54.0 V 88.0% DLG75PS54 100 W 12.0 V 8.30 A 9.0-12.0 V 88.0% DLG100PS12 (3) 100 W 15.0 V 6.60 A 10.0-15.0 V 88.0% DLG100PS15 100 W 24.0 V 4.20 A 14.0-24.0 V 90.0% DLG100PS24 100 W 30.0 V 3.30 A 22.0-30.0 V 90.0% DLG100PS30 100 W 36.0 V 2.80 A 26.0-36.0 V 90.0% DLG100PS36 100 W 48.0 V 2.10 A 34.0-48.0 V 90.5% DLG100PS48 (3) 100 W 57.0 V 1.75 A 43.0-57.0 V 90.5% DLG100PS57 132 W 12.0 V 11.00 A 9.0-12.0 V 88.0% DLG150PS12 (3) 150 W 15.0 V 10.00 A 11.0-15.0 V 88.0% DLG150PS15 150 W 24.0 V 6.30 A 14.0-24.0 V 90.0% DLG150PS24 150 W 30.0 V 5.00 A 22.0-30.0 V 90.0% DLG150PS30 150 W 36.0 V 4.20 A 26.0-36.0 V 90.0% DLG150PS36 150 W 48.0 V 3.20 A 33.0-48.0 V 90.0% DLG150PS48 (3) 150 W 54.0 V 2.80 A 38.0-54.0 V 90.0% DLG150PS54 Notes 1. Typical efficiency at full load and 230 VAC input. 3. Not UL8750 approved. 2. Measured using 12 twisted pair with 0.1 F and 47 F capacitors in parallel at 20 MHz bandwidth. Mechanical Details A B 0.28 (7.0) 2.68 (68.0) C 0.35 (8.9) DLG50/75 DLG100/150 4-R2.1 AC IN DC OUT ACL A 6.93 (176.0) 8.74 (222.0) 1.35 (34.2) V+ (RED) ACN V- (BLACK) B 6.38 (162.0) 8.19 (208.0) 18 AWGx2C (DLG50/75/100- 18AWGx3C C 6.03 (153.2) 7.83 (199.0) see note 4 below) 14 AWGx2C (DLG150) 0.35 (8.9) Notes 11.810.79 (30020) 11.810.79 (30020) 1. All dimensions shown in inches (mm). 2. Weight: DLG50/75: 1.98 lbs (900 g) 1.54 (39.0) DLG100/150 2.29 lbs (1040 g) 3. Tolerance: 0.02 (0.5) 4. DLG100PS12 and DLG100PS15 output cable is 14 AWG. Application Notes Constant Voltage / Constant Current Curve Vo max Vo min Trip & Restart Zone 0 10 20 30 40 50 60 70 80 90 100 Output Current (%) Derating Curve 100 100 A A B B C 80 80 60 60 C A DLG150 at 115 VAC 40 40 B DLG150 at 230 VAC & DLG100 A DLG50/75 C DLG50/75 B DLG100 20 20 C DLG150 0 0 0 10 20 30 40 50 55 60 70 90 100 115 130 180 220 240 305 Ambient Temp (C) -30 for DLG100/150 Input Voltage (VAC) 60Hz -40 for DLG50/75 Ta= 25C 16-Dec-14 Load (%) Output Voltage Load (%)