DTE06 DIN CLIP XP Power

DC-DC Converter DTE06 Series 6 Watts Regulated single & dual outputs from 5VDC to 48VDC xxx Series Wide 4:1 input range Fully encapsulated chassis mount Optional DIN rail version IEC/UL/cUL62368-1 safety approvals EN55032 class A with no external components Remote on/off 3kVDC isolation -40C to +105C operating temperature Full power to 80C Dimensions: MTBF >4Mhrs (MIL-DHBK-27F, +25C GB) DTE06: 2.09 x 1.34 x 1.04 (53.0 x 34.0 x 26.5 mm) 3 year warranty Available in two wide (4:1) input ranges for nominal 12/24VDC and 24/48VDC, the DTE06 series of encapsulated 6W DC-DC converters are chassis mount as standard or can be ordered with a DIN rail mount. They have screw terminals for ease of connection and an LED provides clear power good indication. Remote On/Off is standard and when inhibited the standby current is just 2.5mA. Isolation is 3kVDC input/output providing excellent separation between supply and load. The modules are fully protected against input undervoltage, short circuit and overload conditions. These features, along with a rugged design and wide operating temperature range make the DTE06 series suitable for a variety of commercial and industrial applications. Models & Ratings (1,4) Input Current Maximum (2) (3 ) Input Voltage Output Voltage Output Current Efficiency Model Number (5) Capacitive Load Max Load No Load 5.1V 1.20 A 315 mA 10 mA 680 F 81% DTE0624S051 12.0 V 0.50 A 298 mA 10 mA 330 F 84% DTE0624S12 15.0 V 0.40 A 298 mA 10 mA 330 F 84% DTE0624S15 24.0 V 0.25 A 294 mA 10 mA 150 F 85% DTE0624S24 24 V (9-36 V) 48.0 V 0.125 A 301 mA 10 mA 68 F 83% DTE0624S48 12.0 V 0.25 A 298 mA 10 mA 150 F 84% DTE0624D12 15.0 V 0.20 A 294 mA 10 mA 150 F 85% DTE0624D15 24.0 V 0.125 A 298 mA 10 mA 68 F 84% DTE0624D24 5.1V 1.20 A 159 mA 8 mA 680 F 80% DTE0648S051 12.0 V 0.50 A 149 mA 8 mA 330 F 84% DTE0648S12 15.0 V 0.40 A 149 mA 8 mA 330 F 84% DTE0648S15 24.0 V 0.25 A 147 mA 8 mA 150 F 85% DTE0648S24 48 V (18-75 V) 48.0 V 0.125 A 151 mA 8 mA 68 F 83% DTE0648S48 12.0 V 0.25 A 147 mA 8 mA 150 F 85% DTE0648D12 15.0 V 0.20 A 147 mA 8 mA 150 F 85% DTE0648D15 24.0 V 0.125 A 149 mA 8 mA 68 F 84% DTE0648D24 Notes 1. Input current measured at nominal input voltage. 4. Input current is typically 2.5mA at nominal input voltage when output is remotely 2. Typical values. turned off. 3. For optional version fitted with DIN Clip add suffix -D e.g. DTE0624S24-D. 5. Per output. DIN Rail mounting clip is available as a separate item, order code DTE06 DIN CLIP. www.xppower.com 1DC-DC Converter DTE06 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions 9 36 VDC 12V & 24V nominal Input Voltage Range 18 75 VDC 24V & 48V nominal Input Current See Models and Ratings table Inrush Current 60/110 A 24V models/48V models External Fuse Required 2A/1A timelag 24V/48V nominal Input Filter Pi type On at >9 V. Off <8.0 V DTE0624 models Undervoltage Lockout On at >18 V. Off <16.0 V DTE0648 models 50 VDC DTE0624 models for 1s Input Surge 100 VDC DTE0648 models for 1s On: Logic High (3.5-12 V) or open circuit Remote On/Off Off: Logic Low (<1.2 V) or short pin 1 to pin 2 Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 5.1 48 V See Models and Ratings table Initial Set Accuracy 2 % At full load Minimum Load 0 A No minimum load required Start Up Delay 30 ms At nominal input voltage Line Regulation 0.5 % From minimum to maximum input voltage Load Regulation 0.5 % 0 - 100% load On dual output models with one output at 25% load and the Cross Regulation 5 % other varied from 10% to 100% load. Transient Response 5 % deviation Recovery to within 1% in <500s for a 25% load change 75 5V-15V output models, 20MHz bandwidth Ripple & Noise mV pk-pk 180 24V, 48V output models, 20MHz bandwidth Short Circuit Protection Trip & Restart (hiccup mode), auto recovery Overload Protection 150 % Trip & Restart (hiccup mode) Temperature Coefficient 0.02 %/ C General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 83 % See Models and Ratings table Isolation 3000 VDC For 60s functional Isolation Resistance 1000 M At 500VDC Input to Output Capacitance 2200 pF Switching Frequency 370 kHz 3 Power Density 3.4 W/in Mean Time Between Failure 4100 kHrs MIL-HDBK-217F, +25C GB Case Material Epoxy potted in plastic case, UL94V-0 Weight 0.108 (49) lb (g) DIN rail option add 0.202 (92.0) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +105 C See derating curve Storage Temperature -50 +125 C Case Temperature +105 C Thermal Impendance 3.12 C/W Natural convection, 20 LFM case to air Humidity 5 95 %RH Non-condensing Cooling Natural convection Altitude 5000 m Operating Shock and Vibration Tested according to IEC60068-2 www.xppower.com 2