DTE6048S24 XP Power

DC-DC Converter DTE60 Series 60 Watts Fully Encapsulated Chassis Mount xxx Series Wide 4:1 Input Range -40 C to +95 C Operating Temperature High Efficiency up to 92 % Optional DIN Rail Version Remote On/Off EN55022 Conducted Level A With No External Components 3 Year Warranty Dimensions: DTE60: 4.41 x 2.67 x 1.5 (112 x 67.8 x 38 mm) Models & Ratings (1,4) Input Current Maximum (2) (3) Input Voltage Output Voltage Output Current Efficiency Model Number No Load Full Load Capacitive Load 5.1 V 12.0 A 100 mA 2.83 A 20,400 F 90% DTE6024S5V1 12.0 V 5.0 A 100 mA 2.75 A 3540 F 91% DTE6024S12 24 V (9-36 V) 24.0 V 2.5 A 110 mA 2.75 A 890 F 91% DTE6024S24 48.0 V 1.25 A 60 mA 2.75 A 220 F 91% DTE6024S48 5.1 V 12.0 A 40 mA 1.40 A 20,400 F 91% DTE6048S5V1 12.0 V 5.0 A 60 mA 1.36 A 3540 F 92% DTE6048S12 48 V (18-75 V) 24.0 V 2.5 A 60 mA 1.37 A 890 F 91% DTE6048S24 48.0 V 1.25 A 50 mA 1.37 A 220 F 91% DTE6048S48 Notes 1. Input current measured at nominal input voltage. 4. Input current is typically 3 mA at nominal input voltage when output is remotely 2. Typical values. turned off. 3. For optional version fitted with Din Clip add suffix -D e.g. DTE6024S24-D. Mechanical Details 3.54 (90.0) 0.43 (11.0) Pin Connections Pin Function 1 Remote On/Off 1.50 4 x 3.5 (38.0) 2 -Vin 3 +Vin 8 4 No Connection 1.97 7 3 (50.0) 0.66 (16.8) 5 +Vout Top View 2 6 0.20 (5.0) 1 6 No Connection 2.67 5 -D Version (67.8) Indication LED 7 -Vout 4 DC- 3.54 (90.0) ON 0.43 (11.0) 8 No Connection Power Good 0.20 Indicator (5.0) 1.50 3.94 (100.0) Notes (38.0) 4.41 (112.0) 1. All dimensions are in inches (mm) 0.66 2. Weight: 0.6 lbs (300 g) approx (16.8) 3. Weight for -D version: 0.706 lbs (353 g) approx 2 4. Terminal wire size 1.5 mm max 0.12 5. Screw terminal torque 4.5 to 6.2 lb-in (3.0) 0.43 (0.5 to 0.7 Nm) (11.0) 6. Case tolerance: 0.02 (0.5) www.xppower.com 1DC-DC Converter DTE60 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions 9 36 VDC 24 V nominal Input Voltage Range 18 75 VDC 48 V nominal Input Current See Models and Ratings table Inrush Current A Input Filter Pi type On at >9 V. Off <7.5 V 24 V models Undervoltage Lockout On at >18 V. Off <16.0 V 48 V models 50 VDC 24 V models for 100 ms Input Surge 100 VDC 48 V models for 100 ms On: Logic High (3.5-12 V) or open circuit Remote On/Off Off: Logic Low (<1.2 V) or short pin 1 to pin 2 Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 5.1 48 V See Models and Ratings table Initial Set Accuracy 1 2 % Minimum Load 0A No minimum load required Start Up Delay 50 ms Line Regulation 0.2 1.5 % Load Regulation 0.5 1.0 % 0 - 10% load Recovery to within 1% in <250 s for a 50% load change Transient Response 5 % deviation at 0.25 A/s rate 100 5.1 V model, 20 MHz bandwidth Ripple & Noise 150 mV pk-pk 12 V & 48 V models, 20 MHz bandwidth 200 48 V model, 20 MHz bandwidth Short Circuit Protection Trip & Restart (hiccup mode), auto recovery Overload Protection 150 % Trip & Restart (hiccup mode) Overvoltage Protection 120 % Zener diode clamp Temperature Coefficient 0.03 %/ C General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 91 % See Models and Ratings table Isolation 2500 VDC For 60 s Isolation Resistance 1000 M At 500 VDC Input to Output Capacitance 3000 pF Switching Frequency 210 kHz 3 Power Density 3.4 W/in Mean Time Between Failure 240 kHrs MIL-HDBK-217F, +25 C GB Weight 0.6 (300) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +95 C See derating curve Storage Temperature -50 +125 C Case Temperature 95 C 3.5 Natural convection 1.95 100 LFM Thermal Impendance C/W (Case to Ambient) 1.61 200 LFM 1.33 400 LFM Humidity 5 95 %RH Non-condensing Cooling Natural convection Shock 3 shocks in each plane, total 18 shocks of 30 g : 11 ms halfsine. Conforms to EN60068-2-27 & EN60068-2-47 Vibration 10-500 Hz at 2 g sweep and endurance at resonance in all 3 planes. Conforms to EN60068-2-6 2