ITZ0948S05 XP Power

DC-DC Converter ITZ Series 9 Watts Ultra Compact SIP8 Package xxx Series Smallest Footprint 9W Converter Single & Dual Outputs 4:1 Input Range Operating Temperature -40C to +85C 1.6kVDC Input to Output Isolation Fully Regulated Output No Minimum Load Required Remote On/Off Dimensions: 3 Year Warranty ITZ: 0.86 x 0.38 x 0.44 (21.9 x 9.6 x 11.2 mm) Models & Ratings (1) Input Current Maximum Input Voltage Output Voltage Output Current Efficiency Model Number (2) No Load Full Load Capacitive Load 3.3 V 2000 mA 9 mA 335 mA 2600 F 82% ITZ0924S3V3 5 V 1600 mA 9 mA 390 mA 1300 F 85% ITZ0924S05 9 V 1000 mA 9 mA 425 mA 800 F 86% ITZ0924S09 12 V 750 mA 9 mA 425 mA 560 F 88% ITZ0924S12 24V 15 V 600 mA 9 mA 420 mA 560 F 89% ITZ0924S15 (9-36 V) 24 V 375 mA 9 mA 420 mA 200 F 89% ITZ0924S24 5 V 800 mA 9 mA 390 mA 800 F 85% ITZ0924D05 12 V 375 mA 9 mA 425 mA 390 F 88% ITZ0924D12 15 V 300 mA 9 mA 430 mA 200 F 88% ITZ0924D15 3.3 V 2000 mA 5 mA 170 mA 2600 F 82% ITZ0948S3V3 5 V 1600 mA 5 mA 195 mA 1300 F 85% ITZ0948S05 9 V 1000 mA 5 mA 215 mA 800 F 86% ITZ0948S09 12 V 750 mA 5 mA 212 mA 560 F 89% ITZ0948S12 48V 15 V 600 mA 5 mA 210 mA 560 F 88% ITZ0948S15 (18-75 V) 24 V 375 mA 5 mA 210 mA 200 F 88% ITZ0948S24 5 V 800 mA 5 mA 195 mA 800 F 85% ITZ0948D05 12 V 375 mA 5 mA 215 mA 390 F 87% ITZ0948D12 15 V 300 mA 5 mA 215 mA 200 F 87% ITZ0948D15 Notes 1. Input currents measured at nominal input voltage. 3. Standard tube quantity = 20 2. Maximum capacitive load is per output. Mechanical Details Pin Connections 0.02 0.38 0.86 (9.60) (0.50) (21.85) Pin Single Dual Printed 1 -Vin -Vin 910 Face 2 +Vin +Vin 0.44 0.42 0.38 (11.20) 3 Remote On/Off Remote On/Off (10.70) 0.01 (9.60) 1 2 3 6 78 0.14 (0.25) 6 +Vout +Vout 11 12 (3.42) 0.02 7 -Vout Common 0.04 0.16 (0.50) (1.00) 8 No Connection -Vout (4.10) 1 23678 9 Case Case 0.42 0.10 0.30 (10.60) 10 Stand Off Stand Off (2.54) (7.62) 11 Stand Off Stand Off 0.70 12 Case Case (17.78) Notes 1. All dimensions are in inches (mm) 4. Pin pitch tolerance: 0.014 (0.35) 2. Weight: 0.257 lbs (7.3 g) approx. 5. Case tolerance: 0.02 (0.5) 3. Pin diameter: 0.020.002 (0.50.05) www.xppower.com 1DC-DC Converter ITZ Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions 9 36 VDC 24 V nominal Input Voltage Range 18 75 VDC 48 V nominal Input Filter Capacitor Input Reflected Ripple 20/40 mA pk-pk 24/48 V input. Through 12 H inductor and 47 F capacitor 50 VDC for 100 ms 24 V models Input Surge 100 VDC for 100 ms 48 V models Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 3.3 30 VDC See Models and Ratings table Initial Set Accuracy 1 % At full load Minimum Load 0A No minimum load required Line Regulation 0.2 % 0.5 % Single output from 0 to full load Load Regulation 1 % Dual output and single 3V3 output from 0 to full load On dual output models when one load is varied between Cross Regulation 5 % 25% and 100% and other is fixed at 100% For 3V3 & 5V output models / all other models. Transient Response 5/3 % deviation Recovery within 2% in less than 2ms for a 25% load change Ripple & Noise 75 mV pk-pk 20 MHz bandwidth. Measured using 0.1 F ceramic capacitor Short Circuit Protection Continuous, with auto recovery Over Voltage Protection 130 % Over Load Protection 180 % Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ C Output is on if remote on/off (pin 3) is open circuit. Output is off if 2-4 mA current is applied to remote on/off (pin 3) via 1 k resistor. Remote On/Off Maxiumum pin voltage is 5 V and maximum current into pin 3 is 4 mA. Note: Output may be affected with current into the pin as low as 10 A. General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 88 % See Models and Ratings table Isolation: Input to Output 1600 VDC For 60 seconds. Insulation: Functional Isolation: Input/Output to Case 1000 VDC For 60 seconds. Insulation: Functional Continuous Working Voltage: 500 VDC 200V r.m.s. Input to Output Switching Frequency 400/500 kHz 24 V input/48 V input 9 Isolation Resistance 10 Isolation Capacitance 50 pF 3 Power Density 65 Win Mean Time Between Failure 900 khrs MIL-HDBK-217F, +25 C GB Case Material Copper Potting Material Epoxy UL94V-0 rated Pin Material Solder coated phosphor bronze C519R-H Solder Profile 260 C max, 1.5mm from case 10s max Weight 0.257 (7.3) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Derate from 100% load at +60 C to no load at +85 C, Operating Temperature -40 +85 C and 100% load at +50 C to no load at +85 C for 3V3 models Storage Temperature -55 +125 C Case Temperature +100 C Humidity 95 %RH Non-condensing Cooling Natural convection www.xppower.com 2