JCM3024D1 XP Power

DC-DC Converter JCM30 Series 30 Watts Single and Dual Outputs xxx Series 1 x 1 Footprint -40 C to +105 C Operation Full Load at 55 C Ambient 1600 VDC Isolation Output Trim 10% Remote On/Off MTBF 370 kHrs 3 Year Warranty Dimensions: JCM30: 1.0 x 1.0 x 0.41 (25.4 x 25.0 x 10.4 mm) Models & Ratings (1) Input Current Input Output Output Max. (3) OVP setting Efficiency Model Number Voltage Voltage Current capacitive load No Load Full Load 3.3 V 7.0 A 10 mA 2215 mA 3.9 V 87% 10000 F JCM3012S3V3 5.0 V 6.0 A 10 mA 2810 mA 6.2 V 89% 7200 F JCM3012S05 12.0 V 2.5 A 12 mA 2810 mA 15.0 V 89% 1200 F JCM3012S12 9-18 V 15.0 V 2.0 A 12 mA 2810 mA 18.0 V 89% 1000 F JCM3012S15 12.0 V 1.25 A 12 mA 2810 mA 15.0 V 89% 750 F JCM3012D12 15 V 1.0 A 14 mA 2780 mA 18.0 V 90% 500 F JCM3012D15 3.3 V 7.0 A 10 mA 1105 mA 3.9 V 87% 10000 F JCM3024S3V3 5 V 6.0 A 10 mA 1390 mA 6.2 V 90% 7200 F JCM3024S05 12 V 2.5 A 10 mA 1375 mA 15.0 V 91% 1200 F JCM3024S12 18-36 V 15 V 2.0 A 10 mA 1375 mA 18.0 V 91% 1000 F JCM3024S15 12 V 1.25 A 10 mA 1375 mA 15.0 V 91% 750 F JCM3024D12 15 V 1.0 A 10 mA 1375 mA 18.0 V 92% 500 F JCM3024D15 3.3 V 7.0 A 8 mA 545 mA 3.9 V 88% 10000 F JCM3048S3V3 5 V 6.0 A 8 mA 695 mA 6.2 V 90% 7200 F JCM3048S05 12 V 2.5 A 8 mA 695 mA 15.0 V 90% 1200 F JCM3048S12 36-75 V 15 V 2.0 A 8 mA 685 mA 18.0 V 91% 1000 F JCM3048S15 12 V 1.25 A 8 mA 685 mA 15.0 V 91% 750 F JCM3048D12 15 V 1.0 A 8 mA 680 mA 18.0 V 92% 500 F JCM3048D15 Notes 1. Input currents measured at nominal input voltage. 3. Add suffix -HK for optional Heat Sink. 2. Maximum capacitive load is per output. Mechanical Details 0.4 0.4 0.41 (10.16) (10.16) (10.4) 0.1 Pin Connections 0.1 0.5 1.0 (25.4) 0.66 (16.8) Top View (2.54) (2.54) (0.02) Pin Single Dual 4 6 Print 5 1 +Vin +Vin 6 54 Face 0.04 (1.0) 2 -Vin -Vin 1.0 0.6 1.0 0.8 (25.4) (15.24) DIA Remote Remote (25.4) (20.32) 3 0.04 On/Off On/Off (1.0) 32 1 4 +Vout +Vout 1 2 3 5 Trim Common 0.24 0.2 0.1 1.0 (25.4) 6 -Vout -Vout 0.1 (6.0) (2.54) (5.08) 0.3 (2.54) (7.62) Notes 1. All dimensions are in inches (mm) 4. Pin pitch tolerance: 0.014 (0.35) 2. Weight: 0.042 lbs (19 g) approx. 5. Case tolerance: 0.02 (0.5) 3. Pin diameter: 0.040.002 (1.0 0.05) www.xppower.com 1DC-DC Converter JCM30 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions 9 18 VDC 12 V nominal Input Voltage Range 18 36 VDC 24 V nominal 36 75 VDC 48 V nominal Input Reflected Ripple Current 30 mA pk-pk Through 12 H inductor and 47 F capacitor 25 VDC for 100 ms 12 V models 50 VDC for 100 ms 24 V models Input Surge 100 VDC for 100 ms 48 V models Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 3.3 30 VDC See Models and Ratings table Output Trim 10 % Single Output Versions Initial Set Accuracy 1 % At full load Minimum Load 0% No minimum load required Line Regulation 0.5 % From minimum to maximum input at full load Load Regulation 0.5/1.0 % From 0% to full load for single/dual output On dual output models, when one output is at 100% load Cross Regulation 5 % and other is varied from 25% load to full load Single output 10 F X7R MLCC Ripple & Noise 75/60 mV pk-pk Dual output with 10 F/25 V X7R MLCC on each output measured using 20 MHz bandwidth Overload Protection 150 % Short Circuit Protection Continuous trip and restart (hiccup), with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ C Over Protection Voltage See Models and Ratings table Output is on if remote on/off (pin 3) is open or high (3.0 to 12 VDC) Remote On/Off Output turns off if remote on/off (pin 3) is low (<1.2 VDC max) General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 92 % See Models and Ratings table Isolation: Input to Output 1600 VDC Isolation: Input to Case 1600 VDC 270 3.3 and 5.0 V Switching Frequency kHz 330 Other models 9 Isolation Resistance 10 Isolation Capacitance 2000 pF 3 Power Density 73 W/in Mean Time Between Failure 370 kHrs MIL-HDBK-217F, +25 C GB Weight 0.042 (19.0) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Derate from 100% load at +55 C to 50% at +80 C or Operating Temperature -40 +100 C from 100% load at 60 C to 50% at 85 C with optional heatsink Storage Temperature -55 +125 C Case Temperature +105 C Humidity 95 %RH Non-condensing Cooling Natural convection www.xppower.com 2