JWL4024S12 XP Power

DC-DC Converter XPPower JWL40 Series 40 Watts Regulated Single & Dual Output xxx Series Wide 4:1 Input Range 2 x 1 Package 1500 VDC Isolation Operating Temperature -40 C to +105 C ITE Safety Approvals Remote On/Off High Power Density Optional Heatsink Dimensions: Six-sided Metal Case JWL40 (24V output): 3 Year Warranty 2.00 x 1.00 x 0.43 (50.8 x 25.4 x 11.0 mm) JWL40 (All other models): 2.00 x 1.00 x 0.40 (50.8 x 25.4 x 10.2 mm) Models & Ratings (1,2) Input current Overvoltage Maximum (4) Input voltage Output voltage Output current Efficiency Model number (3) No load Full load Protection capacitive load 3V3 8.00 A 90 mA 1.24 A 3.9 V 21000 F 89% JWL4024S3V3 5 V 8.00 A 90 mA 1.85 A 6.2 V 13600 F 90% JWL4024S05 12 V 3.33 A 95 mA 1.87 A 15.0 V 2400 F 89% JWL4024S12 9-36V 15 V 2.67 A 105 mA 1.87 A 18.0 V 1500 F 89% JWL4024S15 24 V 1.67 A 115 mA 1.84 A 30 V 600 F 91% JWL4024S24 12 V 1.67 A 65 mA 1.89 A 15.0 V 1200 F 88% JWL4024D12 15 V 1.33 A 65 mA 1.89 A 18.0 V 750 F 88% JWL4024D15 3V3 8.00 A 55 mA 0.62 A 3.9 V 21000 F 89% JWL4048S3V3 5 V 8.00 A 55 mA 0.93 A 6.2 V 13600 F 90% JWL4048S05 12 V 3.33 A 69 mA 0.93 A 15.0 V 2400 F 90% JWL4048S12 18-75V 15 V 2.67 A 65 mA 0.93 A 18.0 V 1500 F 90% JWL4048S15 24 V 1.67 A 75 mA 0.92 A 30 V 600 F 91% JWL4048S24 12 V 1.67 A 45 mA 0.95 A 15.0 V 1200 F 88% JWL4048D12 15 V 1.33 A 45 mA 0.95 A 18.0 V 750 F 88% JWL4048D15 Notes 1. Input currents measured at nominal input voltage. 3. Maximum capacitive load is per output. 2. Input current is typically 2.5 mA at nominal input voltage when output 4. Add suffix -HK for optional heatsink. is turned off using remote on/off. Mechanical Details Optional Heatsink (-HK) 0.40 0.20 0.20 Pin Connections (10.16) (5.08) (5.08) Pin Single Dual 3 2 1 1 +Vin +Vin 2 -Vin -Vin 3 Remote On/Off Remote On/Off 4 +Vout +Vout Bottom View 5 -Vout Common 6 Trim -Vout 0.07 B Notes (1.85) 6 54 1.22 (31.0) Max 1. All dimensions are in inches (mm) Heat-sink 0.22 A 2. Weight: 0.066 lbs (30.0g) approx. Thermal pad 0.40 0.40 0.10 (5.5) (10.16) (10.16) (2.54) 3. Tolerance: X.XX0.01 (X.X0.25) Clamp A: 0.43 (11.0) for 24 V models 1.00 (25.4) Converter 0.40 (10.2) for all other models X.XXX0.005 (X.XX0.13) B: 0.71 (18.0) for 24 V models 0.68 (17.2) for all other models 4. Pin Tolerance: 0.002 (0.05) www.xppower.com 1 0.14 (3.6) 1.80 (45.72) 2.00 (50.8) 0.04 (1.00) 1.22 (31.1)DC-DC Converter XPPower JWL40 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions 9 36 VDC 24 V nominal Input Voltage Range 18 75 VDC 48 V nominal Input Filter Internal Pi type 50 24 V models Input Surge VDC for 1 s 100 48 V models ON: Logic high (3.5-12 V) or open circuit Remote On/Off OFF: Logic low (<1.2 V) or short pin 2 to pin 3 Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 3.3 30 VDC See Models and Ratings table Initial Set Accuracy 1.0 % At full load Output Trim 10 % See Application Notes Output Voltage Balance 2.0 % For dual output with balanced laods Minimum Load A No minimum load required Line Regulation 0.5 % From minimum to maximum input at full load Load Regulation 0.5/1.0 % Single / Dual output, from 0 to full load On dual output models when one load is varied between Cross Regulation 5.0 % 25% and 100% and other is fixed at 100% Recovery within 1% in less than 250 s for a 25% load Transient Response 3 5 % deviation change. 3.3 & 5V output / other models. 20 MHz bandwidth. Ripple & Noise 100/150 mV pk-pk Measured using 0.47 F ceramic capacitor. Overload Protection 150 % Short Circuit Protection Continuous Trip & Restart (Hiccup mode), with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ C General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 90 % See Models and Ratings table Isolation: Input to Output 1500/1800 VDC 60 s/1 s 9 Isolation Resistance 10 At 500 VDC Isolation Capacitance 1500 pF Switching Frequency 285 kHz 3 Power Density 50.0 W/in Mean Time Between Failure 320 KHrs MIL-HDBK-217F, +25 C GB Weight 0.066 (30.0) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +105 C See Derating Curve. Storage Temperature -50 +125 C Case Temperature +105 C Humidity 95 %RH Non-condensing Cooling Natural convection Thermal Impedance to Air 12/10 C/W No heatsink / with heatsink EMC: Emissions Phenomenon Standard Test Level Notes & Conditions Conducted EN55022 Class A See Application Notes www.xppower.com 2