QHL600300S24 XP Power

DC-DC Converter QHL600 Series 600 Watts 180 - 425 VDC input range xxx Series Single output Industry standard full brick -40 C to +100 C operation 3000 VAC isolation Output trim -40% to +10% Remote on/off Current share and power good signals 3 year warranty Dimensions: The QHL600 series offers a compact 600W DC-DC solution in an industry standard full brick QHL600: package. This series of modules enables effective construction of distributed power architectures 4.6 x 2.4 x 0.5 (116.8 x 61.0 x 12.7 mm) from AC front ends, PFC front ends and battery systems. Models & Ratings (1) Input Current Input Output Ripple & Max. capacitive (1) Output Current Efficiency Model Number (2) (3) Voltage Voltage noise load No Load Full Load 12 V 50.0 A 10 mA 2.24 A 150 mV 89.5% 10000 F QHL600300S12 300 24 V 25.0 A 10 mA 2.21 A 240 mV 90.5% 10000 F QHL600300S24 (180-425 V) 48 V 12.5 A 10 mA 2.20 A 480 mV 91.0% 8000 F QHL600300S48 Notes 1. Measured at 300 VDC input. 2. Peak to peak measured at 20MHz bandwidth and 470 F electrolytic/1 F ceramic capacitors. 3. Minimum capacitive load of 470 F required to maintain regulation. Mechanical Details 4.099(104.11) Pin Connections 3.949(100.30) 3.799(96.49) Pin Function 3.649(92.68) 1 -Vin 3.499(88.87) 3.349(85.06) 2 +Vin 3 REM- 16 15 14 13 12 11 4 REM+ 10 5-7 +Vout -Vo 1.40 1 9 -Vin (35.5) 8-10 -Vout -Vo 1.70 0.90 8 2.0 11 -Sense (43.2) 2.40 2 -Vo (22.8) (50.8) +Vin (61.0) 12 +Sense 1.30 (33.0) - 2.25 7 13 Trim 3 +Vo (57.1) 14 Current Share 4 6 0.90 + +Vo (22.8) 15 Power Good 5 0.75 +Vo (19.0) 16 Auxiliary, 7-13 V/20 mA Notes 0.199(5.05) 0.40 0.50 1. All dimensions are in inches (mm) 4.20(106.7) (10.1) (12.7) 2. Weight: 0.51 lbs (230 g) approx. Mounting Inserts 3.5 through 4 places 0.20 3. Tolerance: x.xx = 0.02 (x.x = 0.5) (5.1) x.xxx = 0.01 (x.xx = 0.25) 0.22 (5.5) 0.50 4.60(116.8) (12.7) www.xppower.com 1 8-0.039(1.00) 8-0.079(2.00) ON/OFF AUX IOG PC/NC TRIM +S -SDC-DC Converter QHL600 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage Range 180 425 VDC Input Current 1.8 3.8 A 425-180 VDC input Input Surge 475 VDC For 100 ms >160 V 170 180 On Undervoltage Lockout VDC <150 V 160 170 Off Lockout Hysteresis 10 VDC Input Transient Voltage 475 VDC For 100 ms Input Overvoltage Lockout 480/500 VDC Module On / Module Off Idle Current 10 mA When output is remotely turned off 2 Inrush Current 1.0 A s Recommended Input Fuse 6.3 A Fast acting type Input Reflected Ripple Current 50 mA pk-pk Through 10 H inductor Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 12 48 VDC See Models and Ratings table Output Trim -40 +10 % See Application Note Initial Set Accuracy 1 % At full load Minimum Load 0 % No minimum load required Line Regulation 0.2 % From minimum to maximum input at full load Load Regulation 0.5 % From 0% to full load Maximum deviation, recovering to less than 1% in Transient Response 3.0 5.0 % 500 s for 25% step load change. Start Up Time 700 ms Output Voltage Rise Time 40 ms Ripple & Noise mV pk-pk See models and ratings table Overload Protection 105 125 % Short Circuit Protection Continuous hiccup mode, with auto recovery See Models and Ratings table. Minimum capacitance of Maximum Capacitive Load 330 F required to meet specified regulations Temperature Coefficient 0.03 %/ C Overvoltage Protection 115 125 140 % Ouput is on if REM+ (pin 4) is open or high (3.5-75 VDC) with respect to REM- (pin 3) or -Vin (positive logic) Remote On/Off Output turns off if REM+ (pin 4) is low (<1.2 VDC max) with respect to REM- (pin 3) or -Vin General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 90 % See Models and Ratings table Isolation: Input to Output 3000 VAC 60 s Isolation: Input to Case 2500 VAC 60 s Isolation: Output to Case 500 VAC 60 s Switching Frequency 200 kHz Fixed, 15% 9 Isolation Resistance 10 M Case Material Plastic (DAP) with aluminium base plate. UL94V-0 rated. Potting Material Epoxy UL94V-0 Pin Material Copper with nickel and matte tin plate Solder Profile 260 C max. Above 250 C 3-6 seconds. With iron 450C for <5s Water Wash Use deionized water, do not soak. Dry thoroughly 3 Power Density 135 W/in Mean Time Between Failure 420 kHrs MIL-HDBK-217F, +25 C GB Weight 0.51 (230.0) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Base Plate Temperature -40 +100 C Storage Temperature -55 +105 C Thermal Protection +105 C Auto recovery at 75 C typical Humidity 95 %RH Non-condensing Cooling Baseplate-cooled Altitude 2000 m Operating. Storage to 12000 m www.xppower.com 2